Sanyo SC-X80 Скачать руководство пользователя

Страница: 13 / 16

1
2

Agitator Assembly

Motor Shaft

Flat Belt

Motor Shaft

Flat Belt

Pulley

REPLACEMENT INSTRUCTIONS

Caution:

Be sure to turn the ON/OFF switch to the "OFF " position and disconnect the

power cord from the wall outlet before replacing any of the parts below.

REPLACING THE FLAT BELT

Remove the bottom plate.
(refer to page 14)

Lift out the agitator assembly,and then remove the flat belt from the motor shaft and
the agitator pulley.

Place a new flat belt onto the motor shaft and pulley.

Holding two ends of the agitator to place the agitator assembly into the grooves by in the
nozzle head, making sure that the new flat belt slides securely into the guide.

Caution:

Install the flat belt so that it has

no twists in it, and so that all

components turn smoothly.

Reattach the bottom plate
(refer to page 14)

Brush Holder

Groove

Содержание SC-X80

















Результаты поиска

Содержание SC-X80

Отзывы:

Похожие инструкции для SC-X80

Бренды по названию

Популярные бренды

Sanyo SC-X80, Инструкция по эксплуатации

Результаты поиска

Содержание SC-X80

Отзывы:

Похожие инструкции для SC-X80

Бренды по названию

Популярные бренды