Sanyo SAP-CRV12AEH Скачать руководство пользователя страница 17

Страница: 17 / 20

English

6. Check After Installation and Test Run

6-1. Check After Installation

Check the items listed in the table below after installing the air conditioner.

6-2. Test Run

6-2-1. Before Test Run

• Do not switch on the power before installation is finished completely.

• Electric wiring must be connected correctly and securely.

• Cut-off valves of the connection tubing should be opened.

• All foreign material such as wire bits and filings must be cleared from the unit.

6-2-2. Test Run Method

• Switch on the power, then press the “ON/OFF” button on the wireless remote controller to start operation.

• Press the MODE button to select COOL, HEAT, or FAN to check whether operation is normal or not.

Items to be checked

Possible malfunction

• Has it been securely mounted?

• The unit may fall over, shake, or

emit noise.

• Have you done the refrigerant leakage

test?

• It may have insufficient cooling (heating)

capacity.

• Is heat insulation sufficient?

• It may cause condensation and dripping.

• Is water drainage adequate?

• It may cause condensation and dripping.

• Is the voltage in accordance with the rated

voltage marked on the nameplate?

• It may cause electrical malfunction or

system damage.

• Is the electric wiring and tubing connection

installed correctly and securely?

• It may cause electrical malfunction or

system damage.

• Has the unit been connected to a secure

ground connection?

• It may cause electrical leakage or

shorting.

• Is the power cord as specified?

• It may cause electrical malfunction or

system damage.

• Is the air intake or outlet covered or

blocked?

• It may cause of insufficient cooling

(heating) capacity.

• Have the lengths of the connection tubing

and refrigerant capacity been recorded?

• The refrigerant amount may not be

correct.

10-061 SAP-KRV9AEH EN 4/27/10 4:42 PM Page 17

Содержание SAP-CRV12AEH





















Результаты поиска

Содержание SAP-CRV12AEH

Отзывы:

Похожие инструкции для SAP-CRV12AEH

Бренды по названию

Популярные бренды

Sanyo SAP-CRV12AEH, Руководство по установке

Результаты поиска

Содержание SAP-CRV12AEH

Отзывы:

Похожие инструкции для SAP-CRV12AEH

Бренды по названию

Популярные бренды