background image

2

• For surface mounting on the wall, see Fig. 2.

1. Insert a screwdriver or the like in the groove on the

lower side of the remote controller to pry off the
back case. (See Fig. 3)

2. Use the 2 supplied M4 

×

25 machine screws for

embeded mounting or M4 

×

25 tapping screws for

surface mounting to secure the remote controller
back case. Prior to mounting, clear the cutouts in
the back case corresponding to the holes in the
wall box using a screwdriver or the like. Use the
spacers and take care not to tighten the screws
excessively. If the back case will not seat properly,
cut the spacers to a suitable thickness.

3. Connect locally supplied 3-core lead wires to the

lead wires from the remote controller. (See “How to
wire the remote controller.”)
(The remote controller will be damaged if
220/240V AC is applied.)

4. Hook the remote controller to the tabs of the back

case and mount it.

How to wire the remote controller

Connection diagram

See Fig. 4.

How to connect the harness (supplied parts)

1. Turn off the power, and remove the grille.

2. Remove the screws of the electrical box and

remove its cover.

3. Pull out the indoor unit controller (PCB ass’y). 

(Fig. 6 on next page)

4. Pull out the lead wire that connects the remote con-

trol receiver to CN11 of the controller (PCB ass’y).
(Fig. 5 on next page)

5. Plug the socket of the supplied wire harness onto

CN11.

6. Bind the wire harness and the inter-unit lead wires

together, and route them. Fasten them under the
electrical box with the clamp. Then, pull them out
from the back of the indoor unit.
If required, connect the lead wire (field supply, max.
10 m). (Fig.4)
Use the supplied wire joints (6 pcs.) to connect the
lead wire. (See the connection diagram as shown at
right.)

Fig. 3

Fig. 4

1

2

3

Indoor

unit

*1
Wiring for remote
controller (supplied locally), Max. 10m

*1: 0.5mm

2

 to 2.0mm

2

 wires are used for lead wires.

Wire joint

Wire joint

Wiring from
remote controller

Wiring from
indoor unit

Remote
Controller

Approx. 200mm

RED

WHT

BLK

RED

WHT

BLK

Lead wire from
indoor unit

6 supplied
white wire
joints 

1. Peel off 14mm of cable

sheathing on each wire.

2. Twist the 2 wires

together and crimp them
together with a wire joint.

3. When a crimping tool is

not used, solder the
wires together and cover
the joint with insulating
tape.

Lead wire
from
remote controller

Wire
joint

Fig. 2

Wall

Under-case (back case)

Remote controller

Tapping screws
M4 

×

 25 (2)

Lead
wires (3)

03-242.Sanyo.85464359404000  8/21/03  9:17 AM  Page 2

Содержание RCS-KS2432AWD

Страница 1: ...llpoint pen or tool with a small tip How to install the remote controller NOTE 1 Do not twist the remote controller wire with the power cord or run them in the same metal conduit because this may cause a malfunction NOTE 2 Install the remote controller away from all sources of electrical noise NOTE 3 Install a noise filter or take other appro priate action if electrical noise affects the power sup...

Страница 2: ...nit controller PCB ass y Fig 6 on next page 4 Pull out the lead wire that connects the remote con trol receiver to CN11 of the controller PCB ass y Fig 5 on next page 5 Plug the socket of the supplied wire harness onto CN11 6 Bind the wire harness and the inter unit lead wires together and route them Fasten them under the electrical box with the clamp Then pull them out from the back of the indoor...

Страница 3: ... ORG YEL BLK FAN MOTOR P S G G G w FM HH H M L LL w w w w w w POWER TRANSFORMER TR1 IND LAMP ASSY RC1 CAPACITOR 1 2 G 4 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 FLP CONNECTOR WHT CONNECTOR WHT WHT WHT FLAP MOTOR UPPER CONTROLLER FLAP MOTOR LOWER ROOM THERMISTOR TH2 COIL THERMISTOR TH1 WHT BLU BLU BLU BLU 8512 5253 714XX 1 KS2432A Electric Wiring Diagram Fig 6 TRANS 1 2 G 4 C B P Controller PCB ass ...

Страница 4: ...e system shifts into cooling oper ation and cool air will start to be felt Cooling oper ation with the switch at the TEST position is unaf fected by the room temperature 5 After stopping the test run turn the operation selec tor switch of the indoor unit to the OFF position once then move to ON position Fig 7 6 Press the ON OFF button on the remote control unit to stop the air conditioner If the u...

Отзывы: