Sanyo PLC-XU301, Руководство по обслуживанию

Страница: 46 / 112

-46-
Electrical Adjustments
Group/
Item
Item Name Function Initial range Note
Group
264
Auto calibration (Ycbcr)
0 Y-OFFSET AREA H START
Y - Offset Acquiring Area H-Start
Position
95 0 - 1000
1 Y-OFFSET AREA V START
Y - Offset Acquiring Area V-Start
Position
500 0 - 1000
CB - OFFSET AREA H
START
CB - Offset Acquiring Area H-Start
Position
95 0 - 1000
3 CB - OFFSET AREA V START CB - Offset Acquiring Area V-Start
Position
500 0 - 1000
4 CR - OFFSET AREA H
START
CR - Offset Acquiring Area H-Start
Position
95 0 - 1000
5 CR - OFFSET AREA V START CR - Offset Acquiring Area V-Start
Position
500 0 - 1000
6 Y - GAIN AREA H START 50 0 - 1000
7 Y - GAIN AREA V START 500 0 - 1000
8 CB - GAIN AREA H START 800 0 - 1000
9 CB - GAIN AREA V START 500 0 - 1000
10 CR - GAIN AREA H START 700 0 - 1000
11 CR - GAIN AREA V START 500 0 - 1000
1 Image AREA H WIDTH YCBCR Level Acquiring Area 13 0 - 4095
13 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 4095
14 Y - OFFSET TARTGET 4 0 - 55
15 CB OFFSET TARGET 18 0 - 55
16 CR OFFSET TARGET 18 0-55
17 Y-GAIN TARGET 17 0-55
18 CB-GAINTARGET 37 0-55
19 CR-GAINTARGET 37 0-55
0 OFFSET torelance Torelance of OFFSET Adj. 1 1-55
1 GAIN torelance Torelance of GAIN Adj. 1 1-55
Group
270
cuStoM(Aspect)
0 Scaler Horizontal Horizontal Scaler Edit 100 68-13
1 Sclaler Vertical Vertical Scaler Edit 100 68-13
Connect Seperate/Connect Edit 0 0-1 0:Seperate, 1: Connect
3 Position Horizontal Horizontal Postion Correction 100 85-115
4 Position Vertical Vertical Position Correct 100 85-115
5 Aspect Enable Aspect Adj. Enable 0 0-1 1: Enable, 0: Disable
Group
280
AutoPc Adjust
0 AutoPCAdjustEnable
Auto-PC Adj Operation Enable if Un-
supported Signal Input
0 0-1 0:Enabel, 1:Disable
1 Frequency Step Frequency Steps of Total Dot 1 0-3
Frequency Threshold Total Dot Freqency Threshold 5 0-10 0[]<-- - --> 10[Not matched]
3 Fine Phase Do Phase Adj after Total Dot Adj. 1 0-1 0;Excutes Fine Phase; 1:Not Excute
4 BLKDET Black Level Detection Area 1 0 - 3
5 PHASEMSK Phase Detection Filter 0 0 - 3
0: Effective All Bit,
1: Disable Lower 1 bit
: Disable Lower bit, 3: Disable
Lower 3 bit
Group
290
Paneltype * Panel type check
0 GammaL/R-View Current Setting Check 0 0-0
0: Gamma for L-Turn
0: Gamma for R-Turn * Read only
1 GammaL/R-Change Setting of Gamma 10 0-0
Sets L-Turn Gamma if the Value is
set to 0.
Sets R-Turn Gamma if the Value is
set to 0.
Group
500
composite (NtSc) composite / S-Video
0
1 Disp Dots
668 0 �� 4095
H Back Porch 8 0 �� 4095
3 V Back Porch 18 0 �� 4095
4 Disp Line 458 0 �� 4095
Group
501
composite (PAl) composite / S-Video
0
1 Disp Dots
658 0 �� 4095
H Back Porch 34 0 �� 4095
3 V Back Porch 0 �� 4095