22
To search a preset station by PTY codes
A particular programme type broadcast can be located by specifying the
PTY codes.
1.
Press the RDS button to select “PTY” while listening to an FM
broadcast.
2.
Press the TUNE/PTY + or – button within 2 seconds to select the
desired PTY code. The PTY code changes as shown below;
NEWS
v
AFFAIRS
v
INFO
v
SPORT
v
EDUCATE
v
DRAMA
v
CULTURE
v
SCIENCE
v
VARIED
v
POP M
v
ROCK M
v
M.O.R. M
v
LIGHT M
v
CLASSICS
v
OTHER M
v
WEATHER
v
FINANCE
v
CHILDREN
v
SOCIAL
v
RELIGION
v
PHONE IN
v
TRAVEL
v
HOBBIES
v
JAZZ
v
COUNTRY
v
NATION M
v
OLDIES
v
FOLK M
v
DOCUMENT
v
TEST
v
ALARM
(or in the reverse sequence)
TIMER OPERATION
Using the timer
Set the on and off times, function to be used and volume level. Operation
will start with the selected function at the on time. The sound will be
gradually increased from a no-sound level to the volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before setting
the timer.
-
Select the function for timer operation and prepare the sources to be
used.
-
If the function selected is tuner, tune in to the desired band and
station.
-
Adjust the volume level as desired.
Operation
1.
Press the SHIFT + 7 TIMER buttons.
The previous timer on time setting appears.
2.
Press the SHIFT + 8 ADJUST buttons within 10 seconds.
3.
Set the hours of timer on time by pressing the
e
or
f
button, then
press the SHIFT + 8 ADJUST buttons.
Set the minutes in the same way.
The timer off time setting appears.
4.
Set the timer off time as described in step 3. The original display
returns, then the timer operation standby mode is activated. “
0
”
remains lit.
5.
Press the
z
/ON button to switch off the power, you will see GOOD
BYE and “
0
” this will go off after 2 seconds.
-
“
0
” blinks during a timer-controlled operation.
-
If you wish to switch off the power during a timer-controlled operation,
press the
z
/ON button and the timer will be set in the standby mode.
To check the timer settings
Press the SHIFT + 7 TIMER buttons repeatedly. The timer settings are
displayed in the following order:
On time
v
Off time
v
Function
v
Original display returns
To change the settings, press the SHIFT + 7 TIMER buttons to select the
setting to be changed, then press the SHIFT + 8 ADJUST buttons so that
the display blinks. Change the setting as explained above.
To release the timer
After turning the power on, press the SHIFT + 7 TIMER buttons, then press
the SHIFT + 9 SET/CLEAR.
To set the timer again with the same settings
1. Press the SHIFT + 7 TIMER buttons, then the SHIFT + 9 SET/CLEAR.
2. Press the
z
/ON button to switch off the power.
Note:
-
If the SHIFT + 9 SET/CLEAR buttons are pressed while the timer is
being set, the original display returns.
-
The timer mode is released if a power failure occurs during timer
controlled operation.
-
The timer may not operate if a power failure occurs during timer
operation standby mode.
Using the sleep timer
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 4 time periods
available: 30, 60, 90 and 120 minutes.
Press the SHIFT + 6 SLEEP buttons repeatedly to select the desired sleep
time. “SLEEP” and the selected time blink on the display. After several
seconds, the original display returns and the brightness of the display
reduces. “SLEEP” blinks.
To check the remaining sleep time
Press the SHIFT + 6 SLEEP buttons once. After several seconds, the
original display returns.
To release the sleep timer while in operation
Press the SHIFT + 6 SLEEP buttons, then press the SHIFT + 9 SET/
CLEAR buttons. The timer is also released if the power is switched off.
x
x
x
x
x
x
x
x
x
x
ON
ON
ON
ON
ON
OFF
3. Press the PTY CHK (
e
) button within 4 seconds.
The unit searches 24 preset stations and stops when it finds a
broadcast of the PTY code you have selected, then tunes into that
station.
-
To continue searching after the first stop, repeat steps 1 - 3 above.
-
If no broadcast is found, the original station is heard.
To cancel searching, press the RDS button.
Содержание DC-TS750
Страница 1: ...INSTRUCTION MANUAL DVD Home Theatre System DC TS750 REMOTE CONTROLLER RB TS750ST ...
Страница 26: ...25 ...
Страница 27: ...26 ...
