Sanyo Carrier 16LJ Series, Руководство по установке

Страница: 20 / 52

20
3.7 - Bubble test
(when the unit is charged)
•___________ml (cm
3
)/10 min
•___________ml (cm
3
)/10 min
•___________ml (cm
3
)/10 min
Refer to the table in the chapter "Bubble test". Take measure-
ments several times to obtain the value given in the table.
3.8 - Verify valve opening status and switch position
Change-over valves
B-valve - in purge pipe (open): ....... Open ® Closed ®
Isolation valves
Valve open/close status should be as follows.
•
Absorption pump (open): ........ Open ® Closed ®
• Refrigerant pump (open): ........ Open ® Closed ®
Diaphragm valves
Valve open/close status should be as follows.
•
Manual purge Valve V1, V2, V3 (closed):
Open ® Closed ®
• Refrigerant blow-down valve (closed):
Open ® Closed ®
Service valves
Valve open/close status should be as follows.
•
Charge/remove N
2
gas: .......................SV1 (closed)
Open ® Closed ®
• Purge unit: ..........................................SV2 (closed)
Open ® Closed ®
• Refrigerant: ........................................SV3 (closed)
Open ® Closed ®
• Diluted solution: .................................SV4 (closed)
Open ® Closed ®
• Concentrated solution: .......................SV6 (closed)
Open ® Closed ®
• Generator pressure gauge: ..................SV7 (open)
Open ® Closed ®
Switch - purge (off):
.......................................On ® Off ®
3.6 - Verify auxiliary equipment
(For confirmation purpose only)
Water piping
• Chilled-water flow direction (inlet/outlet):
Good ® Not good ®
• Cooling water flow direction (inlet/outlet):
Good ® Not good ®
• Hot water flow direction (inlet/outlet):
Good ® Not good ®
• Chilled-water inlet/outlet valves: Open ® Closed ®
• Cooling water inlet/outlet valves: Open ® Closed ®
• Hot water inlet/outlet valves: Open ® Closed ®
Air vent valve, drain valve, pressure gauge, thermometer
Water circuit Air vent Drain valve Pressure Thermo-
valve gauge meter
Chilled water Yes No Yes No Yes No Yes No
Cooling water Yes No Yes No Yes No Yes No
Water pump duty
• Chilled water pump : ____________kW*
• Cooling water pump : ____________kW*
• Hot water pump : ____________kW*
Cooling tower
: ____________kW*
* For information only
Cooling water temperature control:
Fan on-off ® 2-way valve ® 3-way valve ®
Water charge into the chilled-water circuit:
Yes ® No ®
Water charge into the cooling water circuit:
Yes ® No ®
Water charge into the hot water circuit:
Yes ® No ®
Automatic cooling water blow-down device:
Yes
®
No
®
Chemical cooling water feeding device:
Yes ® No ®
Check cooling water temperature control:
Good ® Not good ®
Water circulating conditions:
Item Chilled water Cooling water
Suction pressure (kPa/MPa) _____________ ___________
Delivery pressure (kPa/MPa) _____________ ___________
Current (A) _____________ ___________
Capacity of a main breaker: _______________A
3.4 - Check of control board safety and switch settings
• Generator pressure gauge (63GH) : _______________kPa/MPa
• Purge tank pressure sensor (69PR) : _______________kPa/MPa
• Absorbent pump thermal relay (51A) : _______________A
• Refrigerant pump thermal relay (51R) : _______________A
• Purge pump thermal relay (51P) : _______________A
3.5 - Check of purge pump
• No water in liquid trap : Yes ® No ®
• Oil quality : Clean ® Not cleaned ® ‡ Replace oil
(or contains water)
• Oil quantity : Good ® Not good ® ‡ Add new oil up to the centre of
sight glass or remove oil.
• Direction of rotation : Good ® (as arrow on V-belt cover) Not good ® ‡ Transpose two power supply wires