13
13
14
14
TROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
When the following problems occur, the microcomputer will detect the abnormal condition
and an electronic buzzer sounds for approximately 10 seconds and digital display
indicates flash as shown below.
NOTE:
The Trouble indicators can be released by pressing the START/PAUSE button
once if you want to release the emergency stop. Then press the START/PAUSE button
again to restart the operation.
1.During Washing or Rinsing, still there is Water inletting. This is possibly automatic water
adding due to water level decrease.
2.Spin tub turns or stops timely at the beginning of spinning. This is intermittent spinning
for better spin effect.
3.No drainage during overflow rinse. This is caused by lower water level set or lower water
pressure.
4.Water inletting and rinsing sometimes during spinning. This is automatic lean-correction
due to clothe is not equally inside.
5.There is sound like water flow after spinning. This is the sound of balance liquid in
Balance ring. It is for reducing vibration of spinning.
6.Control panel keeps warm after Power Off, this is caused by Remember circuitry
working.
7.Power off during working and the washer could not continue working. Should set the
program again.
VARIOUS FUNCTIONS
VARIOUS FUNCTIONS
NO TROUBLE CONDITIONS
NO TROUBLE CONDITIONS
OTHERS
OTHERS
Kind of Trouble
The washer
does not work
at all
●
●
●
●
●
●
Check the POWER ON/OFF button.
Check the START/PAUSE button.
Check whether under PRESET condition.
Check the power cord whether is securely plugged in.
Check whether power failure occurs.
Check whether the fuse or circuit breaker has been
activated.
●
●
●
●
●
Turn on the water supply faucet.
Check whether water supply has been cut off.
Check whether the metal filter in water inlet is clogged.
Check whether washer has been freezing.
Check whether water pressure is too low.
●
●
●
Check whether the Drain Hose has been put down.
Check whether the drain hose rises too high.
Check whether the drain hose is clogged.
●
●
Check whether the laundry is clumped on one side of tub.
Check whether the washer is on the level surface.
●
Close the washer lid.
●
●
Check whether the washer is under Child Lock.
Close the washer lid.
Press the POWER ON/OFF button, call the local
service-person or dealer.
Water does
not flow into
tub or water
flow is slim
Water does
not drain out
The washer
does not spin
Does not wash
Other troubles
Trouble
Indication
Where to Check
Water Inlet
Filter
Clean the water inlet valve
(Suggest clean it every 6 months)
After long time use, The water inlet mesh
bag may be blocked with crud,
please load off the water inlet hose,
take out the water inlet mesh bag
from the water inlet valve, clean
the mesh bag, then assemble
the mesh bag in the valve and
load the water inlet hose.
Clean lint filter
(Suggest clean it every week)
1. Take out the lint filter
2. Pull out the scraps and wash
the lint filter in the water.
3. Install the Filter.
aim the frame claw to the
groove below.
( Lint Filer is easily destroyed parts).
Clean washing machine
Use soft clothing to wipe off the water or
dirt on the surface of the washer.
● Do not spray water directly
to the washer body.
● Detergent, propellant and
other chemicals are not
allowed to use to avoid the
damages on the surface.
Clean “ magic ” hose joint filter
(Suggest clean it every 6 months)
1. Pull the water inlet hose out.
2. Turn off the revolver according to
below figure.
3. Load off the “ Magic ” Hose Joint
filter and clean the crud with a
toothbrush.
4. Install the clean “ Magic ” Hose Joint
filter to revolver and water inlet hose.
CARE AND MAINTENANCE
CARE AND MAINTENANCE
1.Delete the end buzzer: Press POWER ON/OFF button to switch on the power, and press
START/PAUSE button for 4 seconds till a sound from buzzer. To restore it, repeat above
or pull out the plug.
2.How to drain remaining water
When select this function, in 9 minutes after the working finished, the drainage valve will
open to drain out the remained water inside. This will avoid water freezing inside in winter
when temperature below 0
℃
.
● Method of Use
Press POWER ON/OFF button to switch on the power, and press PROCESS button for
4 seconds till a sound from buzzer. To restore it, repeat above or pull out the plug.
℃
