Sanyo 48 series страница 163 Скачать руководство пользователя

Страница: 163 / 275

2-18

2-21. Table of Self-Diagnostic Functions and Corrections (X, T, U, D Types)

Wired remote
controller
display

Indoor unit
receiver lamp

Cause

Correction

Group connection and simultaneous-operation multi
system

Nothing is
displayed

Nothing is
displayed.

• Remote controller is not connected with indoor unit

correctly.

• Indoor unit power is not ON.

Connect the remote controller correctly. Turn ON the
indoor unit power.

E01

displayed

Operation lamp
is blinking.

• Automatic address setting has not been completed.
• Inter-unit control wiring is cut or is not connected

correctly.

• Remote controller is not connected with indoor unit

correctly.

Check the remote controller and inter-unit control
wiring.
Perform automatic address setting (2-22).

E02

displayed

• Remote controller is not connected with indoor unit

correctly.

Connect the remote controller correctly.

E14

displayed

• Remote controller crossover wiring is cut or is not

connected correctly.

Check the remote controller crossover wiring.
Perform automatic address setting again.

E04

displayed

Standby lamp is
blinking.

• Indoor-outdoor inter-unit wiring is not connected

correctly.

Connect the wiring correctly.

E06

displayed

• Inter-unit control wiring is cut or is not connected

correctly.

Refer to 2-22-1. Basic wiring diagram, and make the
correct setting.

E15

displayed

• Indoor unit capacity is too low.

Check that the total capacities of the indoor and
outdoor units are appropriate.

E16

displayed

• Indoor unit capacity is too high.

P05

displayed

Operation lamp
and Standby
lamp are blinking
alternately.

• Reversed phase at one of the outdoor units in the group.
• Insufficient gas

Reverse 2 phases of the outdoor unit 3-phase power
and connect them correctly.
Fill up the gas appropriately.

P09

displayed

Timer lamp and
Standby lamp
are blinking
alternately.

• Ceiling panel connector at one of the indoor units in the

group is not connected correctly.

Connect the indoor unit ceiling panel connector
correctly.

P12

displayed

• DC fan trouble at one of the indoor units in the group.

Check whether the fan holder is loose.
Check the wiring between the DC fan and the PCB.

L02
L13

displayed

Both the
Operation lamp
and Standby
lamp are blinking
together.

• Indoor-outdoor unit type mismatch.

Check that the indoor and outdoor unit types are
correct.

L07

displayed

• Remote controller crossover wiring is connected to the

indoor unit, however it is set for individual operation.

Perform automatic address setting (2-22).

L10

displayed

• Check outdoor operation with separate maintenance-use remote controller.

SM830161̲Book.indb 18

2008/06/03 9:09:03

Содержание 48 series




















































































































































































































































































Результаты поиска

Содержание 48 series

Отзывы:

Похожие инструкции для 48 series

Бренды по названию

Популярные бренды

Sanyo 48 series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание 48 series

Отзывы:

Похожие инструкции для 48 series

Бренды по названию

Популярные бренды