Sanyo 48 series страница 157 Скачать руководство пользователя

Страница: 157 / 275

2-12

2-15. Table of Self-Diagnostic Functions and Corrections (K Type)

Wired remote
controller
display
(Field supply)

Indoor unit
receiver lamp

Cause

Correction

1:1 connection (Single type)

Group connection
(Simultaneous multi
system)

Nothing is
displayed

• Indoor operation switch is OFF.
• Indoor unit power is not ON.

• Same at left.

• Set the indoor operation switch ON.
• Turn ON the indoor unit power.

E01

displayed

Operating lamp
is blinking.

• Automatic address setting has not been

completed.

• Inter-unit control wiring is cut or is not

connected correctly.

• Same at left.

• Check the inter-unit control wiring.
• Perform automatic address setting.
(See 2-16.)

E14

displayed

——————

• Remote controller

crossover wiring is cut
or is not connected
correctly.

• Check the remote controller crossover

wiring.

• Perform automatic address setting again.

E04

displayed

Standby lamp is
blinking.

• Indoor-outdoor inter-unit wiring is not

connected correctly.

• Same at left.

• Connect the wiring correctly.

E06

displayed

——————

• Inter-unit control

wiring is cut or is not
connected correctly.

• Refer to 2-16 System Control, and make

the correct settings.

E15

displayed

• Indoor unit capacity is too low.

• Same at left.

• Check that the total capacities of the indoor

and outdoor units are appropriate.

E16

displayed

• Indoor unit capacity is too high.

• Same at left.

• Reverse 2 phases of the outdoor unit

3-phase power and connect them correctly.

P05

displayed

Operation lamp
and Standby
lamp are blinking
alternately.

• Reversed phase in the outdoor unit

single-phase or open phase in the
outdoor unit 3-phase power.

• Same at left.

• Connect the units correctly.

L02

displayed

Both the
Operation lamp
and Standby
lamp are blinking
together.

• Indoor-outdoor unit type mismatch.

• Same at left.

• Connect the units correctly.

L13

displayed

• Indoor-outdoor units are not setting

correctly.

• Same at left.

• Connect the units correctly.

L04

displayed

——————

• Outdoor unit address is

duplicated.

• Connect the units correctly.

L07

displayed

——————

• Remote controller

crossover wiring is
connected to the indoor
unit, however, it is set
for individual operation.

• Perform automatic address setting.
(See 2-16.)

P15

displayed

Operation lamp
and Standby
lamp are blinking
alternately.

• No gas

• Same at left.

• Check the refrigerant cycle (for gas leaks).

SM830161̲Book.indb 12

2008/06/03 9:09:03

Содержание 48 series




















































































































































































































































































Результаты поиска

Содержание 48 series

Отзывы:

Похожие инструкции для 48 series

Бренды по названию

Популярные бренды

Sanyo 48 series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание 48 series

Отзывы:

Похожие инструкции для 48 series

Бренды по названию

Популярные бренды