manualshive.com logo in svg

Sanwa PM3, Инструкция по эксплуатации, Страница: 12 / 16

Поделиться
Скачать
Sanwa PM3 Скачать руководство пользователя страница 12

●

Make sure that the test leads are not cut, referring to the section.

6-2 Calibration

The dealer may conduct the calibration and inspection. For more
information, please contact the dealer.

6-3 How to Replace Battery

WARNING

1. If the rear case is removed with input applied to the input terminals,

you may get electrical shock. Before starting the work, always
make sure that no inputs is applied.

2. Be sure to use the fuse is same rating so as to ensure safety and

performance of tester.

3. When operators remove the rear case, do not touch the internal

parts or wire with hand.

＜

How to replace the battery

＞

①

Remove the rear case

screw with a screwdriver.

②

Remove the rear case.

③

Take out the battery and replace it with a 

new one.

④

Attach the rear case and fix it with the screw.

CAUTION

Set a battery with its polarities
facing in the correct directions.

6-4 Storage 

CAUTION

1. The panel and the case are not resistant to volatile solvent and 

must not be cleaned with thinner or alcohol. For cleaning, use 
dry, soft cloth and wipe it lightly.

2. The panel and the case are not resistant to heat. Do not place 

the instrument near heat-generating devices (such as a soldering iron)

3. Do not store the instrument in a place where it may be subjected 

to vibration or from where it may fall.

4. For storing the instrument, avoid hot, cold or humid places or places. 

Under direct sunlight or where condensation is anticipated.
Following the above instructions, store the instrument in good environment.

Coin type
lithium battery
CR2032

Screw

ー 11 ー

Содержание PM3

















Отзывы:

Нет отзывов