Sanwa PDR4000 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

Sanwa PDR4000 Скачать руководство пользователя страница 13

− 11 −

• When the resistance of the auxiliary earth electrode H (C)

exceeds about 12 kΩ, the display is "- - - -".

[6] MAINTENANCE

1. This section is very important for safety. Read and understand

the following instruction fully and maintain your instrument properly.

2. The instrument must be calibrated and inspected at least once

a year to maintain the safety and accuracy.

6-1 Maintenance and inspection

1) Appearance

• Is the appearance not damaged by falling?

2) Test leads

• Is the the test leads not damaged or the core wire not

exposed at any place of the test leads?

If any of the above is found with the appearance, do not use

the equipment and have it repaired.

6-2 Calibration

The manufacturer may conduct the calibration and inspection. For

more information, please contact the dealers.

6-3 Cleaning and storage

1. The main unit is not resistant to volatile solvent and must

not be cleaned with lacquer thinner or alcohol. If it gets

dirty, wipe lightly with a soft cloth moistened with a small

amount of water.

2. The main unit is not resistant to heat. Do not place it near a

source of high heat.

3. Do not store the instrument in a place where it may be

subjected to excessive vibrations or from where it may fall.

4. For storing the instrument, avoid hot, cold or humid places or

placed under direct sunlight or where condensation is anticipated.

5. When the instrument is not to be used for a long period, be

sure to remove batteries from it.

CAUTION

WARNING

«
...
11
12
13
14
15
...
»

Содержание PDR4000





















Отзывы:

Нет отзывов