(6901-002111 <02>)
17
6 Ajustes
Consulte la página 11
1.
Ajuste la tensión del giro a la izquierda/derecha.
PRECAUCIÓN:
Nunca retire la tuerca de tensión
(A)
. Asegúrese de que las roscas son visibles por encima de la tuerca.
2.
Ajuste la tensión de extensión/retracción del brazo.
3.
Ajuste la tensión de la inclinación hacia arriba/abajo.
2 Montaje en pared Montante de madera
Consulte la página 7
2-1 Localice los montantes
Si necesita ayuda para determinar la posición de la placa de pared, consulte Height Finder en sanus.com.
Localice los montantes. Verifique el centro de los montantes utilizando un punzón, un clavo fino o un localizador de montantes de borde a borde.
PRECAUCIÓN:
Evite posibles lesiones personales y daños materiales.
Ù
Ningún material que cubra la pared debe superar los 16 mm (5/8 in.).
Ù
Tamaño mínimo del montante de madera: común 51x102 mm (2 x 4 in.) (nominal 38x89 mm /1,5 x 3,5 in).
2-2 Marque la pared
Consulte la página 7
Nivele la placa de pared
[02]
y marque la posición de los orificios.
NOTA:
El televisor se inclinará 9 cm (3,5 in.) a la derecha o a la izquierda en la posición inicial.
Tenga esto en cuenta cuando seleccione la ubicación de la montura de pared.
2-3 Taladre los orificios guía
Consulte la página 7
Taladre los orificios guía tal como se ilustra en la imagen.
Los orificios guía
DEBEN
taladrarse hasta una profundidad de 89 mm (3,5 in.), utilizando una broca de 5,5 mm (7/32 in.) de diámetro.
2-4 Apriete los pernos tirafondo
Consulte la página 7
Apriete los pernos tirafondo.
PRECAUCIÓN:
Evite posibles lesiones o daños materiales. El uso
incorrecto
podría
reducir
la
capacidad de
sujeción
del
perno
tirafondo.
Para
evitar
posibles
lesiones
o
daños
materiales
Ù
NO
apriete excesivamente los pernos tirafondo
[17]
.
Ù
Apriete los pernos tirafondo solo hasta que las arandelas
[16]
queden firmemente sujetas contra la placa de pared
[02]
.
2 Montaje en pared
Hormigón macizo o bloque de hormigón
Consulte la página 8
2-1 Marque la pared
Consulte la página 8
Si necesita ayuda para determinar la posición de la placa de pared, consulte Height Finder en sanus.com.
Nivele la placa de pared
[02]
y marque la posición de los orificios.
PRECAUCIÓN:
Evite posibles lesiones o daños materiales.
Ù
Monte la placa de pared
[02]
directamente sobre la superficie de hormigón.
Ù
Grosor mínimo del hormigón macizo: 203 mm (8 in.)
Ù
Tamaño mínimo del bloque de hormigón: 203x203x406 mm (8x8x16 in.)
2-3 Inserte los anclajes y los pernos tirafondo
Consulte la página 8
Inserte los anclajes de los pernos tirafondo
[18]
. A continuación inserte los pernos tirafondo
[17]
a través de la placa de pared
[02]
en los anclajes.
PRECAUCIÓN:
Evite posibles lesiones o daños materiales. El uso
incorrecto
podría
reducir
la
capacidad de
sujeción
del
perno
tirafondo.
Para
evitar
posibles
lesiones
o
daños
materiales:
Ù
Asegúrese
de
que
los anclajes
[18]
están asentados
al mismo
nivel
que
la
superficie de hormigón.
Ù
Apriete
los
pernos
tirafondo
[17]
solo
hasta que
las arandelas
[16]
queden
firmemente
sujetas
contra
la
placa
de pared
[02]
.
Ù
NO
apriete excesivamente
los
pernos
tirafondo
[17]
.
2-2 Taladre los orificios guía
Consulte la página 8
Taladre los orificios guía tal como se ilustra en la imagen.
PRECAUCIÓN:
Evite posibles lesiones o daños materiales. :
Ù
Los orificios
guía
DEBEN
taladrarse
hasta
una
profundidad
de
89
mm
(3.5
in.)
utilizando
una
broca de 10 mm
(3/8
in.)
de
diámetro.
Ù
Nunca
taladre
en
el
mortero
entre
los bloques.
3 Colocación del brazo en la placa de pared
Consulte la página 9
4 Colocación del televisor en el brazo
Consulte la página 9
Coloque el brazo
[03]
de modo que el codo quede presionado contra la pared. Apriete el ajuste de tensión
(T)
para evitar que los brazos se muevan mientras
instala el soporte del televisor.
Coloque el soporte del televisor
[01]
en el conjunto del brazo
[03]
. Se escuchará un clic cuando las partes queden montadas correctamente.
INCLINE EL TELEVISOR HACIA ARRIBA.
Instale y apriete el tornillo de bloqueo
[13]
.
Alinee
los
orificios
de
la
parte
superior
e
inferior
del
brazo
[03]
con
las
ranuras
de
la
placa
de pared
[02]
.
Coloque las placas
[21]
y
el
brazo
[03]
en
la
placa
de pared
[02]
utilizando
la arandela
[19]
y
el tornillo
[20]
. Fíjelos con la llave Allen
[23]
.
5 Gestión de cables
Consulte la página 10
Retire las cubiertas del brazo.
Estire cada brazo hasta su máxima extensión y luego dirija los cables a través del brazo. Deje suficiente holgura para evitar tirar del cable cuando se mueve el brazo.
Vuelva a colocar las cubiertas del brazo. Instale las cubiertas superior e inferior
[22]
.
6-1
Consulte la página 11
Ajuste
del nivel.
A.
Afloje
los tornillos
B.
Ajuste
el nivel
C.
Apriete de nuevo
los tornillos