manualshive.com logo in svg

Santon AH10/2.2, Инструкция по установке и эксплуатации, Страница: 2 / 12

Поделиться
Скачать
Santon AH10/2.2 Скачать руководство пользователя страница 2

2

Please read and understand these instructions prior to installing your Aquaheat  un-

vented water heater. Particular attention should be paid to the section headed 

IM-

PORTANT INSTALLATION POINTS

. Following installation and commissioning 

the operation of the heater should be explained to the customer and these instructions 
left with them for future reference.

TECHNICAL SPECIFICATION

Electrical rating  ....................................................2.0kW @ 230V 

.............................................................................. 2.2kW @ 240V 

Capacities  .............................................................7, 10 or 15 litres

Weight (full)  .........................................................7 litre - 11.9 kg 

...............................................................................10 litre - 15.9 kg 

...............................................................................15 litre - 25.0 kg

Rated pressure  ......................................................6 bar (0.6 MPa)

Minimum recommended supply pressure  ............0.8 bar (0.08 MPa)

Pressure Relief Valve  ...........................................6 bar (0.6 MPa)

Name

Aquaheat

Model identifier

7l

(2.2kW)

10l

(2.2kW)

15l

(2.2kW)

Storage volume V (litres)

7.0

10.0

15.0

Mixed water @ 40°C V40 (l)

13

17

25

Load Profile

XXS

XXS

XXS

Energy Efficiency Class

C

C

C

Energy Efficiency %

31.3

30.6

30.8

Annual electricity consumption kWh

589

603

599

Daily fuel consumption kWh

2.860

2.940

2.920

Thermostat setting

60°C

Specific precautions that shall be taken when the 

water heater is assembled, installed or maintained 

and disposed of at end of life. 

See sections 1 to 9

Table: Technical parameters in accordance with European Commision 

regulations 814/2013 and 812/2013

The HWA Charter Statement requires that all members adhere to the following:

• 

To supply fit for purpose products clearly and honestly described.

•  To supply products that meet, or exceed appropriate standards and building and 

water regulations.

•  To provide pre and post sales technical support.

•  To provide clear and concise warranty details to customers.

Содержание AH10/2.2













Отзывы:

Нет отзывов