manualshive.com logo in svg

Sandpiper S30, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Sandpiper S30 Скачать руководство пользователя страница 13

520-222-000

1/04   Rev C

Model S30 Metallic Design Level 1   Page 11

RECYCLING

Many components of SANDPIPER

®

Metallic AODD pumps are made of
recyclable materials (see chart on page
10 for material specifications). We
encourage pump users to recycle worn
out parts and pumps whenever possible,
after any hazardous pumped fluids are
thoroughly flushed.

This pump is pressurized
internally with air pressure
during operation. Always
make certain that all bolting
is in good condition and that

all of the correct bolting is reinstalled during
assembly.

WARNING

Before pump operation,
inspect all gasketed
fasteners for looseness
caused by gasket creep.
Re-torque loose fasteners

to prevent leakage. Follow recommended
torques stated in this manual.

CAUTION

When used for toxic or
aggressive fluids, the pump
should always be flushed
clean prior to disassembly.

WARNING

Before maintenance or
repair, shut off the com-
pressed air line, bleed the
pressure, and disconnect
the air line from the pump.

The discharge line may be pressurized and
must be bled of its pressure.

WARNING

Take action to prevent static
sparking. Fire or explosion
can result, especially when
handling flammable liquids.
The pump, piping, valves,

containers or other miscellaneous equipment must
be grounded. (See page 28)

WARNING

IMPORTANT

Read these safety warnings
and instructions in this
manual completely, before
installation and start-up
of the pump. It is the

responsibility of the purchaser to retain this
manual for reference. Failure to comply with
the recommendations stated in this manual will
damage the pump, and void factory warranty.

WARNING

Airborne particles and loud
noise hazards.

Wear ear and eye protection.

Before doing any main-
tenance on the pump, be
certain all pressure is
completely vented from the
pump, suction, discharge,

piping, and all other openings and connections.
Be certain the air supply is locked out or made
non-operational, so that it cannot be started while
work is being done on the pump. Be certain that
approved eye protection and protective clothing
are worn all times in the vicinity of the pump.
Failure to follow these recommendations may
result in serious injury or death.

WARNING

WARNING

In the event of diaphragm
rupture, pumped material
may enter the air end of the
pump, and be discharged
into the atmosphere. If

pumping a product which is hazardous or toxic,
the air exhaust must be piped to an appropriate
area for safe disposition.

IMPORTANT SAFETY

INFORMATION

CE

Pump complies with EN809 Pumping Directive and
Directive 98/37/EC Safety of Machinery, and ATEX 100a
Directive 94/9/EC Equipment for use in Potentially
Explosive Environments. For reference to the directive
certificates visit: www.warrenrupp.com

I M2 c/b T5
II 2GD b T5

Содержание S30

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды