S&P HTB-75 N, Руководство пользователя

Страница: 11 / 36

11
MANTENIMIENTO
NOTA IMPORTANTE: Antes de iniciar el mantenimiento del ventilador, asegúrese de que está
desconectado de la red eléctrica.
1.- La limpieza periódica es el único mantenimiento requerido.
2.- Limpie el ventilador con un cepillo blanco o un trapo suave para evitar daños al acabado.
3.- En el momento del mantenimiento, tenga precaución en no apoyarse sobre las palas, ya que
éstas se podrían desequilibrar y aumentaría el balanceo del ventilador.
4.- No utilice agentes de limpieza abrasivos, ya que estos pueden dañar el acabado.
5.- No utilice agua en la limpieza del ventilador ya que puede causar daños en el motor.
SOLUCIONAR PROBLEMAS
NOTA IMPORTANTE: Antes de manipular el ventilador, asegúrese de que está desconectado de
la red eléctrica.
Problema Causa problema Solución sugerida
Ventilador no arranca
Ventilador ruidoso
Ventilador tiembla o vibra
en exceso
1.Fusibles fundidos o interrup-
tor general desconectado.
2.Conexiones flojas en las re-
gletas de conexión.
3.Palas de la hélice no fijadas
al ventilador
4.Tornillos flojos.
5.Tornillos flojos entre las palas
y el soporte motor.
6.Las palas de la hélice no es-
tán bien asentadas.
7.El soporte no está bien suje-
tado al techo.
8.Las palas de la hélice están
fuera equilibrio.
1.Comprobar fusibles o inte-
rruptor general.
2.comprobar conexiones.
3.Unir palas al ventilador antes
de arrancar.
4.Comprobar todos los tornillos
del ventilador
5.Comprobar los tornillos que
fijan las palas a la carcasa del
motor y apretar si es necesario.
6.Comprobar que todas las pa-
las están bien asentadas y con
el mismo ángulo de inclinación.
7.Comprobar el anclaje del so-
porte gancho.
8.Cambiar unas palas de posi-
ción.
8
ENGLISH
Installation Manual and Operating Instructions
C
aution : For safe operation and installation, read all instructions carefully
Neither the manufacture nor the manufacturer’s agent/distributor nor the retailer from whom
this product was purchased shall be in anyway responsible for any loss or damage of whatever
nature caused by the installation of this product
.
GENERAL SAFETY RULES
To ensure the success of the Ceiling Fan’s installation, be sure to read the following general safety
rules before begining .
1- The Ceiling Fan installation should be carried out by a qualified electrician.
2- To ensure a correct installation, be sure to read the instructions and review the diagrams thoroughly
before commencement.
3- All electrical connections must be carried out in accordance with local codes and regulations, or
the national Electrical Code. If you are unfamiliar with the installation of electrical wiring, secure
the services of a qualified electrician.
4- Electrical supply 230V AC 50 Hz
5- These apparatus must be earthed.
6-The method of disconnection from the mains supply must incorporate a switch or isolator with a
minimum contact separation of 3 mm.on all poles.
7- Make sure that when the fan is fitted in the chosen position there is not possibility of the rotating
blades coming into contact with any object. Blades should be at least 2.30 m from floor when fan
is hung.
8-If you are installing more than one ceiling fan make sure that you do not mix fan blade sets, even
though they are from the same ceiling fan model.
9-Before beginning, disconnect power by removing fuse or turning off circuit breaker.
10-Once fan installation is completed make sure that all connections are secure to prevent fan from
falling.
11-Do not insert anything into the fan blades when ceiling fan is operating.
IMPORTANT NOTE : The warnings,safeguards and instructions given in this manual are not
exhaustive and do not nessecarily cover all eventualities. It must be understood that common sense,
caution and care are factors which cannot be built into any product. These factors must be supplied
by the person(s) caring for and operating the unit.
9 8
SAFETY INSTRUCTIONS
To ensure the success of the Ceiling Fan’s installation, be sure to read the
following general safety rules before begining.
1.- The Ceiling Fan installation should be carried out by a qualified electrician.
2.- To ensure a correct installation, be sure to read the instructions and re-
view the diagrams thoroughly before commencement.
3.- All electrical connections must be carried out in accordance with local codes
and regulations, or the national Electrical Code. If you are unfamiliar with the
installation of electrical wiring, secure the services of a qualified electrician.
4.- Electrical supply: 230V AC 50 Hz.
5.- These apparatus must be earthed.
6.- The method of disconnection from the mains supply must incorporate a
switch or isolator with a minimum contact separation of 3 mm. on all poles.
7.- Make sure that when the fan is fitted in the chosen position there is not
possibility of the rotating blades coming into contact with any object.
Blades should be at least 2.30 m from floor when fan is hung.
8.- If you are installing more than one ceiling fan make sure that you do not
mix fan blade sets, even though they are from the same ceiling fan model.
9.- Before beginning, disconnect power by removing fuse or turning off cir-
cuit breaker.
10.- Once fan installation is completed make sure that all connections are
secure to prevent fan from falling.
11.- Do not insert anything into the fan blades when ceiling fan is operating.
12.- This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruc-
tion concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
13.- Cleaning and maintenance to perform by the user not be made by chil-
dren without supervision.
14.- Each fan will be controlled by its selector. The selector cannot be used
to control by more than one fan.