SANDIA aerospace SA 3/L/NVG Скачать руководство пользователя страница 5

Страница: 5 / 29

Section 1 General Description

1.1 Introduction

This manual describes the installation of the

SANDIA aerospace

MARC70 line of interface mod-

ules. It is intended for use by FAA certified repair stations to install the MARC70 modules. It

includes both the mechanical and electrical installation information for all MARC70 components,

including the individual modules and enclosures. Where applicable, alignment and checkout proce-

dures are included. In many instances, such as with switching relays, the checkout procedure will be

performed as part of the major system installation check out and no specific check out procedure is

provided for in this manual. In any case, the installer should insure that all functions are operating

according to their intended purpose in their particular installation.

1.1.1 Interface Modules

All interface modules have the same mechanical dimensions and are inserted into the card enclosures

in the same manner. An identification tag accompanies each interface module which should be at

tached to the card enclosure directly above the interface module to identify it. Each interface module

connectors, except the SR 34, SR 54 and SR 64, is keyed to prevent the inadvertent installation of

the connector into the wrong module. Keying of the module has been accomplished at the factory by

the removal of one of the pins on the module’s connector. The installing agency MUST insert a key-

ing plug into the appropriate pin location on the harness connector to complete the keying process.

Each MARC70 interface module is FAA-PMA approved and has been tested to meet the require-

ments necessary to allow it to be mounted outside the aircraft’s pressure vessel. Each interface mod-

ule has passed the vibration requirements for helicopter installations. See section 1-2 for complete

technical specification on each of the MARC70 modules.

1.1.2 Card Enclosures

Several different card enclosures are available depending on the application and installation space

available. If an enclosure is not filled, the unused card slots are covered with blank panels. These

extra card slots can be used in future installations or system upgrades, eliminating the need to re-

engineer the mechanical installation. Interface modules are secured to the enclosures with captive

stainless steel screws. In installations where the enclosure is difficult to reach, the harness connector

can be attached first then the module inserted into the appropriate card slot and secured with the cap

tive hold down screws.

1.1.3 SRU-1

The SRU 1 is a single card enclosure which accepts any MARC70 interface module. The SRU 1 is

ideally suited for installations where only one MARC70 card is required or where there is limited

real estate for mounting the larger enclosures. The SRU 1 can be mounted in any axis and either

inside or outside the pressure vessel.

1.1.4 SRU 5

Page 4

Содержание SA 3/L/NVG






























Результаты поиска

Содержание SA 3/L/NVG

Отзывы:

Похожие инструкции для SA 3/L/NVG

Бренды по названию

Популярные бренды

SANDIA aerospace SA 3/L/NVG, Руководство по установке

Результаты поиска

Содержание SA 3/L/NVG

Отзывы:

Похожие инструкции для SA 3/L/NVG

Бренды по названию

Популярные бренды