background image

26

    S&C Instruction Sheet 761-505

Installation

(d)  Move the blade in the 

opening

 direction and 

verify each blade shunt contact fi rmly engages 
its respective interrupter housing before the 
blade contacts disengage from the stationary 
main contact assemblies. See Figure 34. The 
shunt contacts may be bent as required to 
conform to these conditions.

(e)  Also, as the blade assembly moves in the 

opening 

direction, the two blade-opening cams must 
simultaneously make positive engagement with 
their respective interrupter opening levers, as 
shown in Figure 35. Simultaneity is essential to 
ensure both interrupters share the interrupting 
duty. The opening lever on one or both 
interrupters may be bent slightly to attain 
opening simultaneity.

(f)  After opening the blade fully, 

slowly 

close the 

blade and verify the two opening cams do not hit 
the interrupter opening levers. See Figure 35.

Figure 34. The blade assembly moving in the opening direction.

Figure 35. Verifying the blade opening cams do not hit the inter-
rupter open ing levers on closing.

Interrupter opening lever

Blade-opening cam

Interrupter 

opening 

lever

Blade 

opening 

cam

Содержание Alduti-Rupter






























Отзывы: