Samsung WM1245A Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 76

background image

- 21 -

Error

Display

Cause/Appearance of Error

Way of Release

Water
level
sensor
abnormal

IE

If higher than 32kHz or lower than 10kHz of water level
sensor frequency is continuously kept for 4sec in every
0.5sec measurement, this error will occur.
(caused by wire-breaking of water level sensor)

Power Off

Temperatu
re sensor
abnormal

tE1

If AD converter data in water temp sensor become larger
than 63,000 (in case of the temp. sensor being open) or less
than 2,000 (in case of the sensor being short-circuited), this
error will occur.

Power Off

tE2

If AD converter data in fan-housing temp sensor become
larger than 63,000 (in case of the temp. sensor being open)
or less than 2,000 (in case of the sensor being short-
circuited), this error will occur.

tE3

If AD converter data in drying-duct temp sensor become
larger than 63,000 (in case of the temp. sensor being open)
or less than 2,000 (in case of the sensor being short-
circuited), this error will occur.

Motor
driving
abnormal

3E1

In case that position detection signal was not detected longer
than a unit set time during the motor starting and driving, it
will be retried 5 times. If it is not detected more than 6 times,
this error will occur. (caused by wire-breaking of haul-sensor
and motor, or by restriction of motor driving.)

Start button

3E2

If an excessive current is detected at IPM, it will be retried 6
times. But if it is detected more than 7 times, this error will
occur.
(caused by short-circuit of motor wire)

3E3

If motor rotates in reverse direction during the motor starting
and driving or abnormal signal is detected at haul sensor, it
will be retried 8 times. But if it is detected more than 9 times,
this error will occur. (caused by motor overload or noise)

3E4

If 8 times retrial of motor positioning is failed during the early
time of motor driving, it will be retried continuously. But if it is
failed more than 32 times, this error will occur. (caused by
wrong connection of haul sensor or motor wire)

Power
abnormal

PHI

If more than 450V of instant voltage is detected at DC Link,
this error will occur.
(caused by an electric failure during the high-speed
dehydration)
Appearance: IPM Low Arm Short Break

If both AC
power signal
and DC link
voltage are
normal, this

Plo

In case that there is no AC power signal for longer than
60mSec, or that less than 125V of DC Link average
voltage is detected, or that less than 175V is detected
during the PHI error, this error will occur. (caused by
instant electric failure or wire break of power cord)
Appearance: Motor-generating current will be charged
through IPM All Open Break.

error will be
released and
proceed the
previous
operation.

4.

ALIGNMENT AND ADJUSTMENTS

4-1 Error Mode

«
...
22
23
24
25
26
...
»

Содержание WM1245A













































































Отзывы:

Нет отзывов

Похожие инструкции для WM1245A

Бренд: bar aid Страницы: 16

Бренд: Malber Страницы: 16

K 2 Premium Horizontal

Бренд: Kärcher Страницы: 132

Бренд: Haier Страницы: 16

Бренд: Spitwater Страницы: 22

Бренд: Baumatic Страницы: 28

SUNJOE SPX9006-PRO

Бренд: SNOWJOE Страницы: 20

Бренд: Kärcher Страницы: 12

Бренд: Philco Страницы: 51

Бренд: Hotpoint Ariston Страницы: 48

Бренд: Hotpoint Страницы: 16

Бренд: Kärcher Страницы: 112

Бренд: Hisense Страницы: 14

Бренд: IPC Страницы: 104

Бренд: NEFF Страницы: 52

Бренд: VYKING FORCE Страницы: 44

Бренд: Zanussi Electrolux Страницы: 21

Бренд: iLive Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды