background image

Water valve connections for the Detergent Drawer

 

Items Packed With Washer 

BOLT-SPANER (10-13mm Wrench) DC60-40146A 
ASSY HOSE WATER  Cold DC97-15648A       
ASSY HOSE WATER  Hot DC97-15648B           
CAP-FIXER DC67-00307A                               
HOSE-HANGER DC62-10278A 

 

When using non-HE detergents, or using too much deter-
gent for the water hardness and soil level of the clothing, 
over sudsing will occur. When this happens there will be 
leaks out of the detergent drawer and door. Please advise 
consumer of proper detergent usage.

 

It is normal for some water to remain in Deter-
gent Drawer after it completes washing.  
Bleach is usually flushed out into the tub at the 
beginning of the washing. Also, its compart-
ment is washed again during the following 
rinse cycle, removing any remnants. 

 

To unlock the door 

if washer is stuck in the door 

locked mode. 

Remove top, remove console, remove screws for 
front panel, pull panel forward. 

Picture “A” pull bottom of plastic cover away from 
front until it pops off. 

Picture “B” pull  down on plastic lever to release 
lock. 

Remove lock assembly to replace plastic cover.

 

 

 

NOTE: Tee 
moved to 
Main Valve 
hose on later 
production. 

Содержание WF210ANW/XAA








Отзывы: