background image

3

4

DVD-ROM DRIVE
SH-D162D(TS-H352D)

BG68-01434A  Rev.00

- http://www.samsung-ODD.com
- http://www.samsung-ODD.com

5

When using one EIDE cable 

Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear 
of the DVD-ROM drive. 

When using two EIDE cable

Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear 
of the DVD-ROM drive. 

- If there is only one Optical drive: select MA (Master).

Hard Drive

Slave Drive (Choose the SL Jumper)

MainBoard

Hard Drive

Master Drive (Choose the MA Jumper)

MainBoard

SEC 1

PRI 1

SEC 1

PRI 1

-If there is two Optical drive, select MA (Master) / SL (Slave).

Hard Drive

Master Drive (Choose the MA Jumper)

Slave Drive (Choose the SL Jumper)

MainBoard

(Choose the MA Jumper) (Choose the SL Jumper)

Emergency eject hole

LED

Disc compartment

Eject Button

If the compartment does not open

when you press the Eject button,

power off the computer, insert a pin

or unfolded paper clip in the hole 

and push firmlhy)

Front

Rear

Sound output terminal

Interface terminal

Digital output 

terminal

Master/slave select terminal

Power terminal

Accessories

User Guide, Screws. 

Design and specifications are subject to change without prior notice.

Introduction

Design and specifications are subject to change without prior notice.

Connecting the Cables to the 
DVD-ROM

Connecting the Cables 

Connecting the power cable

• The 4-pin power cable from the internal power unit of your computer must 

be connected to the power terminal the rear of the DVD-ROM drive.

1

Connecting the EIDE cable from a sound card

•Connect the 4-pin audio cable between the sound output terminal on the 

DVD-ROM drive and the audio input terminal on the sound card.

4

Installing a jumper on the master/slave select terminal

•Connect a jumper to the rear side of the DVD-ROM.

If the jumper is connected to MA (Master), it will work in the Master mode. 
If the jumper is connected to SL (Slave), it will work in the Slave mode. 
If the jumper is connected to CS (CSEL), you can control the device by using the 
host interface signal CSEL. (In general, connection to MA is recommended.)

2

Connecting the EIDE cable

•Insert the EIDE cable (40-pin), which is connected to the hard 

disk to the interface terminal.
(Place the red line of the cable close to the Pin 1.)

3

Power cable

EIDE cable

Master/slave select terminal

Audio cable

CS : Cable Select(CSEL)
SL : Slave
MA: Master

6

7

Installing the Drive  

Installing the DVD-ROM Drive

If necessary, attach a horizontal bracket

to both sides of the drive.

• You can purchase these accessories separately 

from your computer dealer.

(Screws for use: M3 X 6 X 4)

1

Remove the plate from a free expansion slot and install the

DVD-ROM drive, as shown in the illustration.

• If you have no free expansion slot, install the drive in place of the 

diskette drive.

• Make sure to use the standardized screws supplied (M3X6).

- To use screws other than M3X6 may result in malfunction.

System Requirements

Intel Pentium 

II

350MHz(or higher), 128 MB of RAM (or higher) with an EIDE interface,

Windows 2000/XP/Vista / Windows NT 4.0 (or higher)

2

How to install the DVD-ROM drive on your PC. First, remove the cover;
connect the cable to the DVD-ROM drive and then to the PC.

DVD-ROM

Drive

Horizontal

Bracket

Plate

Using the Drive/Storing and Cleaning
Your Discs

Push the power button and boot the computer.

1

After booting the computer, open the disc 

compartment by pressing the Eject button.

2

Insert the disc (CD) with the label on the disc

facing upwards and close the disc compartment

by pressing the Eject button. The indicator light

comes on.

3

Play the disc (CD).

4

Using the DVD-ROM Drive

Do not place a disc in direct sunlight.

Store a disc vertically in a well-ventilated and 
stable location.

Do not write or attach a label on a disc.

Do not drop a disc or place heavy objects on it.

Do not touch the surface 
of a disc; hold it by the 
edges.

To clean a disc, polish lightly 

from the inside of the disc to the 
outside with a soft cotton cloth.

Storing Your Discs

Cleaning Your Discs

Run the CD player program supplied with the sound card or play the 
Windows Media Player.

Playing CD-DA/Audio CDs

Follow the instructions provided with the disc.

•A video card or MPEG software and a sound card need to be installed to view video CDs.  

Playing Video CDs

The disc may not function properly if there are fingerprints, foreign substances or 
dust on the disc surface.

If the drive is vertically installed, you cannot use an 8 cm Mini Disc 
because the disc is movable. 

8

9

Solving Technical Problems

The DVD-ROM drive is not
detected by the computer.

After installing the DVD-ROM
drive, the PC gets slower.

Check that the power, audio and EIDE cables are correctly 

connected to the computer.

Change the EIDE cable and reconnect it to the computer. 

Preferably, connect a second EIDE cable to the DVD-ROM 

drive in master mode.

Check the position of the jumper in the master/slave select 

terminal.

The DVD-ROM drive is not
recognized by MS-DOS.

Reinstall the device driver or update it with the latest version 

by downloading it from the Samsung Web site.

- http:// www.samsung-ODD.com

- http:// www.samsung.com

The DVD-ROM drive is not
detected by Windows.

This case may occur when there is a Windows installation 

problem; reinstall Windows.

When the MPEG software
plays a Video CD, the pictures
are not regular and the running
speed is too slow.

Adjust the size of the replay screen.

After checking the display resolution, adjust it, if necessary.

A CD is not read or is read
too slowly.

Check whether the CD is of good quality and clean it, 
if necessary.

The disc compartment will
not open.

Check that the power cable is correctly connected.

Power off and disconnect the PC.
Insert a pin or unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.

The DVD-ROM drive is not
detected after it is connected
to a sound card.

The interface mode of the sound card is AT-BUS.

You must therefore connect the DVD-ROM drive to the EIDE 

port on the PC mother board, rather than to the sound card, 

or install an EIDE compatible sound card.

The Disc is not in message is
displayed even though a disc
has been inserted.

The computer may not recognize the disc if you start playback 

too quickly after inserting the disc. 

Open and close the disc compartment and try again. 

Clean the disc and try again.

The friction noise generated during SPIN-UP and STOP is caused by the
Automatic Ball Balancing System(ABS) and is not a malfunction.

Technical Specifications

SH-D162D(TS-H352D)

SECTIONS

DISC

DRIVE 
PERFORMANCE

FRONT PANEL

REAR PANEL

GENERAL

ERROR RATE

OPERATING
ENVIRONMENT

Disc types supported

Disc diameter

Data transfer rate

Sustained

PIO mode 4

Access time(RANDOM) 

Data Buffer capacity

Slide mechanism

Spindle motor

Load mechanism

Eject button

Required power

Interface connector

Audio output

Indicator(LED)

CD-DA(Audio), CD-ROM, CD-R, CD-RW, Photo-CD
(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV,
CD-TEXT,CD-Plus, DVD-ROM, DVD-VIDEO, DVD+R, DVD-R,
DVD+RW, DVD-RW, DVD-RAM, DVD+R/-R Dual 

120mm or 80mm

Max. 21,600KB/sec(16X)

16.6MB/sec

DMA mode 2 

UDMA mode 2 

16.6MB/sec

33.3MB/sec

Max. 7,200KB/sec (48X)

CD

DVD

110ms (typical)

198KB

Laser

Semiconductor laser

Stepping motor

Brushless  Sensorless  DC motor

Tray. DC motor (Soft Eject). Horizontal/Vertical.

10

-15

Mode 1:10

-12, 

Mode 2:10

-9

Eject, Insert

1.5A (rms)

ATAPI

Line out 0.7V ± 20% : 47kΩ

BUSY

Jumper block

Operations

Molex 70203 or other compatible models

Temperature: 5~45°C Humidity: 10~80%

Storage

Temperature: -25~60°C Humidity: 10~90%

Dimensions

148.2 (W) x 42 (H) x 170 (D) mm (including bezel)

Net weight

740 g

User Guide - ENGLISH

FCC Compliance

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be 
deter-mined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This marking shown on the product or its literature,indicates that it should not be disposed with
other household wastes at the end of its working life.To prevent possible harm to the
environment or human health from uncontrolled waste disposal,please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,or their
local government office,for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract.This product should not be mixed with other commercial wastes for disposal.

CAUTION

Change or modifications not expressly approved by the manufacturer responsible for

compliance could void the user ’s authority to operate the equipment.

LASER STANDARD

IEC 60825-1 :1993 +A1 :1997 +A2 :2001

WEEE

Correct Disposal of This Product (Waste Electrical &Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)

• 

Samsung Eco-mark

The Samsung’s own Eco mark helps consumers to easily understand that
Samsung develops eco-friendly products. This mark represents Samsung’s
continuous effort to develop eco-friendly products.                   

• RoHS 

(Restriction of the use of certain hazardous substances in electrical and electronic equipment)
The RoHS, the environment regulation announced by European Union, restricts the use of
lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the
market in The European Union after July 1, 2006. 

Safety Precautions

The following are basic precautions to ensure user safety 
and reduce the risk of property damage.

1

2

Place the drive on a level 
surface.

Do not place the drive in 
direct sunlight.

Avoid low- or high-temperature 
environments. 

Avoid high-humidity environments.

Handle with caution to prevent 
damage from external shock.

Do not drop the drive, and
protect it fromsevere shocks.

It can damage the drive or cause 
it to malfunction.

Do not move the drive while in operation and 

do not attempt to open the disc tray byforce.  

Make sure to close all working programs before

attempting to open the tray and always use the

open/close button.

Do not use cracked, distorted or
damaged discs.

Do not insert a pin into the emergency

opening while in operation.

In particular, a disc with a crack on the 
inner tracks may break while in use.

Never allow food particles or 
foreign substances to enter the 
drive casing. 

To protect against the risk of 
fire, do ot spill such liquids as 
alcohol and benzene on the 
drive.

Do not disassemble, attempt to repair
or modify the device without express
approval as directed in the manual. 

To reduce the risk of damage, 
electric shock, and fire.

Important to read and understand 

at all times

Do not disassemble

1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that

you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is  likely to grow and it
will eventually result in irreparable damage to the disc.

2.  Do not use low quality discs (i.e., illegal products, scratched or damaged discs).

• Any change or modification not expressly approved by designated qualified personnel could 

void your authority to operate this device.

Warning/Caution

Warning:

To warn the user that failure to comply with the instructions may result in 
serious injury or death.

Caution:

To caution the user that failure to comply with the instructions may result in 
damage to property.

Failure to do so may cause the 
device to fall onto a hard surface, 
resulting in damage or malfunction.

• 

If the power cable is not connected

properly, it may cause a fire or

damage the drive. Check the direction

of the power connector and the drive

incline before connection.

+5V DC

Ground

Ground

+12V DC

When you install the drive

While operating

Other

SH-D162D(TS-H352D)ENG/RUS  2007.5.30  11:55 AM  Page 1

Отзывы: