Samsung SF-76x series Скачать руководство пользователя

Страница: 8 / 103

1. Precautions

1.2.5. Disregarding this warning may cause bodily injury

1) Be careful with the high temperature part.

The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser unit to
cool down before disassembly.

2) Do not put fingers or hair into the rotating parts.

When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan, etc.).
If do, you can get harm.

3) When you move the printer, use safe lifting and handling techniques.

This printer is heavy. Use the lifting handles located on each side of the machine. Back injury could be caused if
you do not lift carefully.

4) Ensure the printer is installed safely.

Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause the
printer to tip or fall possibly causing personal injury or damaging the printer.

5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.

1-4

Содержание SF-76x series







































































































Результаты поиска

Содержание SF-76x series

Отзывы:

Похожие инструкции для SF-76x series

Бренды по названию

Популярные бренды

Samsung SF-76x series, Руководство по обслуживанию

Результаты поиска

Содержание SF-76x series

Отзывы:

Похожие инструкции для SF-76x series

Бренды по названию

Популярные бренды