Samsung SCC-C4201(P), Руководство пользователя

Страница: 15 / 18

27 28
Specifications
5
SCC-C4201/C4203
Item Description Remark
- 22x Zoom Camera
- DC 12V ± 10%
- 5.0 W
- NTSC Standard Color System
- 1/4 inch IT CCD
- 768(H) x 494 (V)
- 525 Line, 2:1 Interlace
- Horizontal : 15,734 Hz (INT)
- Vertical : 59.94 Hz (INT)
- INT Only
- 480 TV Lines
- - 50dB (AGC Off)
- 1 Lux (AGC Max, Sense Up 2x)
- 0.02 Lux (Sense Up 128x)
- 0.005 Lux (B/W Mode, Sense Up 128x,
SCC-C4203 Only)
- ATW/ AWC/ Manual MODE
(3200°K, 5600°K, R/B Gain Control)
- Composite Video Out : 1.0 Vp-p
75ohms/BNC
- 22x Zoom Lens in a single unit
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide), F3.8(Tele)
- IR Filter On/Off (SCC-C4203 Only)
- Off, 1/100, 1/250, 1/500, 1/1K, 1/2K,
1/4K, /10K sec
- Off / On (Area Setting)
- Off/Auto 2x~128x/Fix 2x~128x
- Off / On (x10), PIP
- Off / On (Area / Sensitivity Setting)
- -14°F ~ +122°F, ~90 %
- 59.5 x 60.5 x 109.5 (H)mm
- 375g
- Below 3000m
Product Type
Power Supply Voltage
Power Consumption
Broadcast System
Imaging Device
Effective Pixe
Scanning Method
Line Frequency
Synchronization Method
Resolution
S/N Ratio
Minimum Scene Illumination
White Balance
Signal Output
Lens
Electronic Shutter
Back Light Compensation
Sense Up
Digital Zoom
Motion Detection
Operating Temperature
and Humidity
Dimensions
Weight
Operating Altitude
EXIT
The EXIT option is used to quit the Setup Menu mode and
return to the Normal Operation mode.
Caution : If you use an infrared light source while in AUTO
mode, AUTO switching malfunction and camera
AF malfunction may occur.
In AUTO mode, AGC will operates in high speed mode, and
you cannot change it manually, as it is indicated by "---".
Press the
ENTER
button.
(SET UP)
CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC ---
WHITE BAL ATW
SPECIAL ...
AUTO FOCUS ONEAF
MOTION DET OFF
PRESET ...
COLOR/BW AUTO...
EXIT QUIT
(BW SETUP)
BURST ON
LEVEL MEDIUM
DWELL TIME S--|----L
RET
- BURST ON : The color burst signal is output together with
black and white composite video signal.
BURST OFF : The color burst signal is not output.
- LEVEL : You can set the brightness level that changes from
COLOR mode to BW mode in 3 steps : LOW, MEDIUM, and
HIGH.
- DWELL TIME : Set the HOLDING time for switching between
COLOR and BW mode depending the changes in the amount
of light. You can set the HOLDING time to 10sec (S), 30sec,
60sec, or 300sec( L).
QUIT : Select to ignore any changes you have made and
restore the previously saved settings.
SAVE : Select to save the settings that have been changed
so far.
PRESET : Select to ignore any changes you have made
and restore the factory default settings.
☞
☞
☞