Samsung RD080HRXGB Скачать руководство пользователя страница 9

Страница: 9 / 60

preparing the installation

_09

ENGLISH

SPACE REQUIREMENTS

•

The space suggested below is based on operating condition of outdoor temperature of 35°C.

If operating condition of outdoor temperature is higher than 35°C, try to have more space.

•

Make sure to clear a passage for a person and air flow.

•

Observe the clearances and dimensions as seen below when installing the outdoor unit.

•

If you install several outdoor units at the same place, observe the space for ventilation and free airflow.

•

If the space for ventilation is insufficient, the air conditioner may not generate performance designed.

Keep in mind that SAMSUNG logo is located on the front side of outdoor unit.

When installing 1 outdoor unit

When installing more than 1 outdoor unit

Note

• The installation space mentioned above is minimum suggested clearance.

• To secure enough service space and performance of system, take account of more sufficient

space.

• The required minimum space between outdoor units for service and performance of system

is at least 100mm.

(Unit : mm)

Wall height unrestricted

(Unit : mm)

Wall height restricted

< Case 1 >

300 or mor

500 or mor

10 or more

200 or more

< Case 3 >

The height

of the wall is

unlimited

Front

< Case 2 >

100 or mor

500 or mor

50 or more

Front

300 or mor

100 or mor

500 or mor

< Case 1 >

300 or mor

500 or mor

10 or more

< Case 2 >

50 or more

200 or more

300 or more

< Case 3 >

The height of the wall

is unlimited

20 or

100 or

400 or

Front



In case of ‘Case 1’ and ‘Case 2’

• The height of the wall should be 1500mm or less in the front

side.

• The height of the wall should be 500mm or less in the air inlet

side.

• The height of the wall is unlimited in the side.
• If the height of the wall exceeds the above value, the

additional height (h1)/2, (h2)/2 should be added to the
service space(S1), (S2) individually.

1500

500

ont side

S1+h1/2

S2+h2/2

Air inlet

(Unit : mm)

RD@@@HHXG_IM_E_33140-3.indd 9

2011-10-25 오후 2:57:37

Содержание RD080HRXGB





























































Результаты поиска

Содержание RD080HRXGB

Отзывы:

Samsung RD080HRXGB, Руководство по установке, Страница: 9 / 60

Результаты поиска

Содержание RD080HRXGB

Отзывы: