Samsung NX583G0VBSR Скачать руководство пользователя страница 56

Страница: 56 / 67

4. Troubleshooting

This document can not be used without Samsung’s authorization.

4-3 Oven Malfunction

Oven temperature rises too fast (Electrical)

*Check to see if oven exceeds

400

℉

(202

℃

)with in 10 Minut

of room temperature operation.

*Check the harness connections

at PCB terminals(T601~T605)

and PCB connector(CN401) to

make sure.

The harness does not have a

short in it.

Oven Temp

rises too

fast

*Faulty broil, bake,DLB or source

control relay (RY601 ~ RY605).

Replace the PCB

* Replace the PCB.

*Check the broil and bake

burner operation.

* Replace with properly sized orifices.

Burner

Hole Size

NG LP

Orifice in. (mm) in. (mm)

Broil 1.64 1.02
Bake 1.90 1.15

NOTE:

High-altitude orifice kits are available.

Yes

*Repair or replace the harness.

END

CN401

Oven Temp Sensor

RY604

Bake Relay

RY603

Bake Relay

T605

T604

N : 120V

RY601

Source

Control

Relay

Содержание NX583G0VBSR




































































Результаты поиска

Содержание NX583G0VBSR

Отзывы:

Бренды по названию

Популярные бренды

Samsung NX583G0VBSR, Руководство по обслуживанию

Результаты поиска

Содержание NX583G0VBSR

Отзывы:

Бренды по названию

Популярные бренды