manualshive.com logo in svg

Samsung NX583G0VBSR, Руководство по обслуживанию

Поделиться
Скачать
Samsung NX583G0VBSR Скачать руководство пользователя страница 44

44

4. Troubleshooting

This document can not be used without Samsung’s authorization.

SYMPTOM

DIAGNOSIS

REMEDY

Oven temperature 

rises too fast .

* 

The oven temperature exceeds 

400˚F(202˚C) within 10 minutes of 

room temperature operation .

* 

Repair or replace the faulty broil or bake 

relay .

* 

Make sure the harness is wired 

correctly and does not have a short 

circuit in it .

* 

Repair or replace the harness .

* 

Make sure the oven burner orifices 

are sized properly for the type of gas 

being used .

* 

Replace with properly sized orifices:

Burner NG

LP

Orifice mm

mm

Broil

1 .64

1 .02

Bake

1 .90

1 .15

       NOTE: 

High-altitude orifice kits are available .

* 

Replace the PCB .

Oven is 

overheating in all 

cooking modes .

* 

“E-0A” will show on the display if the 

oven temperature reaches 650°F 

(343°C) in any cooking function, 

except self clean .

* 

Check the source control relay (RY01) and 

replace if it is not working properly .

* 

Make sure all harness wires are securely 

fastened .

* 

Check the resistance of oven temperature 

sensor connector on the PCB . (Normal : 

2850Ω)

* 

Replace the PCB .

Membrane control 

keypads are not 

working properly .

* 

Make sure the door lock feature is 

not turned on .

* 

Unlock the controls by pressing and 

holding the lock key for 3 or more 

seconds .

* 

Check to see if the sabbath function 

has been turned on .

* 

Press and hold the Sabbath pad for at least 

3 seconds . The display will show the time of 

day when the function is turned off .

* 

Check the membrane control 

harness and connectors (CN08) 

on the PCB and membrane control 

panel .

* 

Reconnect securely or replace damaged 

membrane control harness .

* 

Check connector (CN08) and/or 

the PCB for damage .

* 

Check the membrane control panel 

for damage .

* 

Replace the PCB assembly . 

(PCB and membrane control panel .)

Содержание NX583G0VBSR




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды