Samsung NX15PRTV05 Скачать руководство пользователя страница 120

Страница: 120 / 257

Troubleshooting 107

Select the desired restore date from the calendar restoration and select the desired
restore point from the list, and then click

Next

The date of the restore point is displayed in bold font.

Confirm the selected restore point and click

Next

. System Restore shuts down

Windows, and starts the restoration processes.

After the restoration is complete, Windows restarts. In the [System Restore
completed] dialog, click

.Your computer has been restored to the selected

restore point.

Undoing the last restoration

The procedures to undo a restoration are described below.

Click

Start > All Programs > Accessories > System Tools > System Restore

Select "Undo my last restoration", and then click

Next

Confirm the restoration information to undo, and than click

Next

. System Restore

shuts down Windows and starts undoing the restoration.

After the undo restoration is complete, Windows restarts. In the [Undo the last
restoration completed] dialog, click

.Your computer has been restored to the

point prior to the last restoration.

Содержание NX15PRTV05


































































































































































































































































Результаты поиска

Содержание NX15PRTV05

Отзывы:

Похожие инструкции для NX15PRTV05

Бренды по названию

Популярные бренды

Samsung NX15PRTV05, Руководство пользователя

Результаты поиска

Содержание NX15PRTV05

Отзывы:

Похожие инструкции для NX15PRTV05

Бренды по названию

Популярные бренды