manualshive.com logo in svg

Samsung MXD-A16K1X025A, Руководство по установке

Поделиться
Скачать
Samsung MXD-A16K1X025A Скачать руководство пользователя страница 9

9

Control-KIT Function

•  Control-KIT uses EEV to control the amount of refrigerant flow and controls the system through outdoor unit and 

wired remote controller.

•  Control-KIT outputs the contact signal for AHU fan operation.  

Terminal block 1, 2 (Refer to page 10) outputs the AHU fan ON contact signal (220~240V) for AHU when operating 
in Cool/Heat/Fan mode. This contact signal output can not be used as power supply for the motor.

•  Terminal block 3, 4 (Refer to page 10) is for AHU-KIT control to receive the fan operation status. This input signal 

should be simple OPEN/SHORT signal without any extra voltage. 
- Normal fan operation : Terminal block 3, 4 is in SHORT. 
- Fan is not in operation : Terminal block 3, 4 is in OPEN. 
- To use fan feedback to protect your system, set the function switch K12(Refer to page 21) to OFF position.

• Connect 220~240V/50Hz to terminal block 1(L)/2(N).
• You should connect outdoor unit communication cable to communication line (F1, F2)(Refer to page 10). 
•  V1, V2(Refer to page 10) is power line for the wired remote controller(12V). 

F3, F4(Refer to page 10) is communication line for wired remote controller.

 

INSTALLATION 

(Continued)

MXD-A16K1X025A_E_31836-1.indd   9

2010-03-12   ｿﾀﾈﾄ 12:42:57

Содержание MXD-A16K1X025A

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды