background image

4-10

Summary of Product

Samsung Electronics

Service Manual

4.3 Main PBA(SPL Model)

The Engine Board and Controller Board have been integrated into a single PBA. This consists of the CPU and
printer control functions. The CPU functions as the bus controller, I/O handler, motor driver and PC interface. The
main board sends the Current Image Video data to the LSU and manages the Electrophotographic printing
process. Circuits on the PBA drive include the main motor (paper feed, cartridge, fuser), clutch driver, pre-transfer
lamp driver, heat-lamp driver and fan driver.
The signals from the paper feed jam sensor and paper empty sensor are inputted to the main board from the
power supply PBA..

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

8

LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS(LD1117DT) U1

LOW POWER DUAL BIPOLAR COMPARATORS(LM393D) U2

SPREAD SPECTRUM CLOCK GENERATOR(CY25811) U4

CPU X-TAL(12MHz) OSC1

SDRAM(K4S641632H) U6, U15

LOW VOLTAGE HEX INVERTER WITH 5V TOLERANT SCHMITT TRIGGER INPUTS(74LCX14) U7

MOTOR DRIVER(A3977SLP) U9

GRAPHIC PROCESSOR ASIC(SPGPM) U11

LOW VOLTAGE HEX INVERTER WITH 5V TOLERANT SCHMITT TRIGGER INPUTS(74LCX14) U24

PARALLEL PORT SINGLE TERMINATION NETWORK(ST1284) U23

LOW VOLTAGE IEEE 161284 TRANSLATING TRANSCEIVER(161284) U22

VIDEO X-TAL(19.6MHz) OSC3

USB 2.0(NET2270) U25

USB X-TAL(30MHz) OSC4

LOW VOLTAGE OCTAL D-TYPE FLIP-FLOP(74LVX273) U14, U19

LOW VOLTAGE BIDIRECTIONAL TRANSCEIVER(74LCX245) U10

FLASH MEMOTY(29LV160DB) U13

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Содержание ML-2251N



















Отзывы: