Samsung HLN507W1X/XAA Скачать руководство пользователя страница 27

Страница: 27 / 90

Alignment and Adjustments

Samsung Electronics

1-25

Engine Failure Inspection Flow Chart for the DMD Board

1) When the power cord is plugged in,

2) DC 380V is automatically supplied to the ballast.

1) When the power key is pressed via the remote control, the

micom of the digital board outputs high (5V) PWR signals.

The power board operates normally

. 5V and 12V are supplied

to the DMD CN105 terminal.

The MTR Reset signal is supplied to the R161 terminal of the

motor IC101 from the micom on the digital board and then the

motor starts to drive.

2) If the color wheel rotates for a certain time and then stops,

check whether the color wheel sensor is normal.

(Check the waveform on the No.2 terminal

below CN102.)

1) Check whether the signal (SCI: ST

CONTROL

INPUT)

that turns on lamp #2 of CN109 on the DMD board is high (5V).

1) Method for checking whether the DDP1010 IC RESET

is normal.

1) Check whether the signal and the voltage are output normally

to the data line of DMD panel.

1) Check whether the DC380V power

is supplied to the ballast.

1) Check whether 5V and 12V are

supplied to the CN105 terminal.

After the set is powered on, check

whether 5V is detected on pin No.49

of IC101.

After a while, the sound generated by

the rotating color wheel is heard.

1) Check whether CN109 #2

signal is 5V

1) If the voltage between R254 and

R255 is 3V

, it is normal.

waveform should be output on the

data line.

* Refer to the remarks.

* For domestic model, it is needed to

check whether the master power switch

is turned on.

The US model has no master power

* 12V must be supplied to operate the

motor

. (The voltage of the motor driving

power is 12V

* If 5V is not detected, the motor will

not operate.

* When SCI is high (5V), the lamp litz of

CN109 is low (0V).

* CN109 #2 terminal voltage changes to

pulse waveform 14 seconds after

(for 50 inch

TV) the time that the

voltage is 5V

* When about 4 seconds have passed

after changing to pulse waveform, the

screens are displayed on the set.

No.

Description

Remark

Key Point

Содержание HLN507W1X/XAA



























































































Результаты поиска

Содержание HLN507W1X/XAA

Отзывы:

Похожие инструкции для HLN507W1X/XAA

Бренды по названию

Популярные бренды

Samsung HLN507W1X/XAA, Руководство по обслуживанию

Результаты поиска

Содержание HLN507W1X/XAA

Отзывы:

Похожие инструкции для HLN507W1X/XAA

Бренды по названию

Популярные бренды