Samsung HLN507W1X/XAA Скачать руководство пользователя страница 10

Страница: 10 / 90

Alignment and Adjustments

1-8

Samsung Electronics

No.

Item

Picture

Description

Remarks

When the

TIMER,LAMP

and TEMP LED

Indicators

filcker simul-

taneously.

1. If the 3 LED indicators flicker from the time the set is

turned on, it means:

1) The CN105 connector on the DMD board is not inserted

properly.

2) The DVI cable that connects the DIGITAL board to the

DMD board is not connected properly.

3) If the lamp does not turn on even after turning it on three

times, by powering off/on 15 second intervals:

The B+ 380V power is not supplied to the ballast

(The cable is not connected properly between the power

and the ballast.)

The cable connected to the CN109 terminal on the

DMD board and the CN2 terminal on the ballast is short-

circuited or not connected.

The lamp does not turn on because 5V has not been

supplied to blue pin #1 on the CN2 terminal of the

ballast.

5V is supplied to the CN2 terminal on the ballast but the

lamp does not turn on because the ballast has a failure.

(If the lamp is replaced and 5V is supplied normally to

the CN2 terminal, suspect a ballast failure if the lamp still

does not turn on.)

The ballast is normal but the lamp doest not turn on.

(When 5V is supplied to CN2 and 385V to CN1, but the

lamp does not turn on, try replacing the lamp. If it turns

on, that means it was a lamp failure.)

4) The color wheel engaged to the engine does not operate,

or the connector which indicates the operation of the

color wheel is not connected properly, and therefore

does not allow the lamp to turn on. The cause can be

determined when the set still does not turn on after

attempting to turn it on three times.

5) Another digital board or the DMD board has a failure.

Conclusively, if the three LED indicators flicker, first

check the above five items, then check the various

connector connections, and then suspect a failure of the

lamp or the ballast.

CN105

DVI cable

Color Wheel Connector

Color Wheel Index Connector

Lamp Connector (OSRAM,Toshiba)

Lamp Connector (Philips)

Ballast CN1 terminal

When measuring voltage make

sure to measure the voltage bet-

ween the two terminals

Ballast CN2 terminal

Содержание HLN507W1X/XAA



























































































Результаты поиска

Содержание HLN507W1X/XAA

Отзывы:

Похожие инструкции для HLN507W1X/XAA

Бренды по названию

Популярные бренды

Samsung HLN507W1X/XAA, Руководство по обслуживанию

Результаты поиска

Содержание HLN507W1X/XAA

Отзывы:

Похожие инструкции для HLN507W1X/XAA

Бренды по названию

Популярные бренды