English
The power LED is off. The screen will not switch on.
Make sure that the power cord is connected.
"No Cable Connected" is displayed on the screen.
Check that the product is connected correctly with a cable.
Check that the device connected to the product is powered on.
"Not Optimum Mode" is displayed.
This message is displayed when a signal from the graphics card exceeds the product's
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and
frequency according to the product specifications.
Français
L'écran ne s'allume pas. L'écran ne s'allume pas.
Vérifiez que le cordon d'alimentation est bien connecté.
"Aucun câble connecté" s'affiche à l'écran (reportez-vous à la section "Connexion à
un ordinateur").
Vérifiez que l'appareil est connecté correctement à l'aide d'un câble.
Assurez-vous que le périphérique connecté à l'appareil est sous tension.
"Mode non optimal" est affiché.
Ce message s'affiche lorsqu'un signal émis par la carte graphique est supérieur à la
fréquence et la résolution maximales de l'appareil.
Consultez le tableau des modes de signal standard et réglez la fréquence et la
résolution maximales conformément aux spécifications de l'appareil.
DEutsch
Die Netz-LED ist ausgeschaltet. Der Bildschirm wird nicht eingeschaltet.
Stellen Sie sicher, dass das Netzkabel korrekt angeschlossen ist.
Die Meldung „Keine Kabelverbindung“ wird auf dem Bildschirm angezeigt (siehe
„Anschließen eines Computers“).
Überprüfen Sie, ob das Gerät korrekt über ein Kabel angeschlossen ist.
Überprüfen Sie, ob das angeschlossene Gerät eingeschaltet ist.
Die Meldung „ungeeign. Modus“ wird angezeigt.
Diese Meldung wird angezeigt, wenn ein Signal von der Grafikkarte die maximale
Aulösung und Frequenz des Geräts überschreitet.
Schlagen Sie in der Tabelle der Standardsignalmodi nach und stellen Sie die maximale
Auflösung und Frequenz gemäß den technischen Daten des Geräts ein.
Magyar
A tápellátás jelzőfénye nem világít. A képernyő nem kapcsol be.
Győződjön meg arról, hogy csatlakoztatva van a tápkábel.
A „No Cable Connected” üzenet látható a képernyőn (lásd: „Csatlakoztatás
számítógéphez”).
Győződjön meg arról, hogy a készülék megfelelően van csatlakoztatva a kábellel.
Ellenőrizze, hogy be van-e kapcsolva a kijelzőhöz csatlakoztatott eszköz.
Megjelenik a „Not Optimum Mode” üzenet.
Ez az üzenet akkor jelenik meg, ha a videokártyától érkező jel felbontása és frekvenciája
meghaladja a készülék maximális felbontását vagy frekvenciáját.
A Szabványos jelmód táblázat alapján állítsa be a készülék műszaki jellemzőinek
megfelelően a maximális felbontást és frekvenciát.
italiano
Il LED di alimentazione è spento. Lo schermo non si accende.
Verificare che la spina di alimentazione sia connessa.
Sullo schermo viene visualizzato il messaggio "Nessun cavo connesso" (vedere
"Collegamento a un PC").
Verificare che il prodotto sia collegato correttamente mediante cavo.
Verificare che il dispositivo collegato al prodotto sia azcceso.
"Mod non ottimale" viene visualizzato a schermo.
Questo messaggio viene visualizzato quando il segnale proveniente dalla scheda
grafica supera la risoluzione e la frequenza massima del prodotto.
Vedere la Tabella delle modalità standard del segnale e impostare la frequenza e la
risoluzione massima in base alle specifiche del prodotto.
Polski
Nie świeci dioda LED zasilania. Ekran się nie włącza.
Upewnij się, że podłączony jest przewód zasilania.
Na ekranie pojawia się komunikat „Nie podłączono kabla” (patrz „Podłączanie do
komputera”).
Upewnij się, że urządzenie jest prawidłowo podłączone kablem.
Sprawdź, czy urządzenie podłączone do monitora jest włączone.
Pojawia się komunikat „Niewłaściwy tryb”.
Komunikat ten pojawia się, gdy sygnał z karty graficznej przekroczy maksymalną
rozdzielczość i częstotliwość urządzenia.
Patrz Tabela trybu standardowego i ustaw maksymalną rozdzielczość i częstotliwość
zgodnie ze specyfikacją urządzenia.
Português
O LED de alimentação está desligado. O ecrã não liga.
Certifique-se de que o cabo de alimentação está ligado.
A mensagem "Nenhum Cabo Ligado" é apresentada no ecrã (consulte "Ligação a
um PC").
Verifique se o produto está ligado correctamente com um cabo
Verifique se o dispositivo ligado ao produto está ligado.
A mensagem "Modo inadequado" é apresentada.
Esta mensagem é apresentada quando um sinal da placa gráfica ultrapassa a
resolução e a frequência máximas do produto.
Consulte a Tabela do modo de sinal padrão e defina a resolução e a frequência
máximas de acordo com as especificações do produto.
EsPañol
El LED de encendido está apagado. La pantalla no se encenderá.
Asegúrese de que el cable de alimentación esté conectado.
"Cable no conectado" se muestra en la pantalla (consulte "Conexión a un PC").
Compruebe que el producto esté conectado correctamente con un cable.
Compruebe que el dispositivo conectado al producto esté encendido.
Se muestra"Modo no óptimo".
Este mensaje se muestra cuando una señal de la tarjeta gráfica supera la frecuencia y
la resolución máxima del producto.
Consulte la Tabla de los modos de señal estándar y configure la frecuencia y la
resolución máximas en función de las especificaciones del producto.
svEnska
Strömlampan är släckt. TSkärmen slås inte på.
Se till att strömsladden är inkopplad.
"Ingen kabel är ansluten" visas på skärmen (se "Ansluta till dator").
Kontrollera att produkten är korrekt ansluten med en kabel.
Kontrollera att enheten som är ansluten till produkten som är påslagen.
Meddelandet "Ej optimalt läge" visas.
Meddelandet visas när en signal från grafikkortet överskrider produktens maximala
upplösning och frekvens.
Se tabellen för standardsignalläge och ställ in maximal frekvens enligt
produktspecifikationerna.
türkçE
Güç LED'i kapalı. Ekran açılmıyor.
Güç kablosunun bağlı olduğundan emin olun.
Ekranda "Kablo Bağlı Değil" görüntüleniyor (bkz. "Bir PC'ye bağlama").
Ürünün bir kabloyla doğru şekilde bağlandığını kontrol edin.
Cihazın bağlı olduğu ürünün açık olduğunu kontrol edin.
"Uygun Olmayan Mod" görüntüleniyor.
Bu mesaj, grafik kartından gelen bir sinyal ürünün maksimum çözünürlüğünü ve
frekansını aştığında görüntülenir.
Standart Sinyal Modu Tablosu'na bakın ve ürünün teknik özelliklerine uygun olarak
maksimum çözünürlüğü ve frekansı ayarlayın.
troubleshooting
see the user’s Manual for further instructions for installation and adjustment.
portez-vous au manuel de l’utilisateur pour obtenir des instructions supplémentaires sur l’installation et le réglage.
licence
Manufactured under licence from Dolby Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
®
Studio Sound
Manufactured under a licence from U.S. Patent No’s: 6,285,767, 8,027,477, 5,319,713, 5,333,201,
5,638,452, 5,771,295, 5,970,152, 5,912,976, 7,200,236, 7,492,907, 8,050,434, 7,720,240, 7,031,474,
7,907,736 and 7,764,802. DTS, the Symbol, and DTS and the Symbol together are registered
trademarks & DTS Studio Sound is a trademark of DTS, Inc.
ⓒ
2012 DTS, Inc. All Rights Reserved.
Premium Sound 5.1
®
Manufactured under a licence from U.S. Patent No’s: 5,956,674; 5,974,380, 5,978,762; 6,487,535;
6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195, 7,930,184, 7,333,929 and 7,548,853.
DTS, the Symbol. and DTS and the Symbol together are registered trademarks & DTS Premium
Sound l 5.1 is a trademark of DTS, Inc.
ⓒ
2012 DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
DivX Certified
Ⓡ
to play DivX
Ⓡ
video up to HD 1080p, including premium content.
DivX
Ⓡ
, DivX Certified
Ⓡ
and associated logos are trademarks of DivX, Inc. and are used under
licence.
ABOUT DIVX VIDEO: DivX
Ⓡ
is a digital video format created by DivX, Inc. This is an official DivX Certified
Ⓡ
device that plays
DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified
Ⓡ
device must be registered in order to play purchased DivX Video-on-
Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
Open source licence notice
In the case of using open source software, Open Source licence are available on the product menu.
Open Source Licence Notice is written only English.
connecting and using a Pc
connecting the Power
using serial MDc
specifications
Model Name
ED32C
ED40C
ED46C
ED55C
Panel
Size
31.5 inches / 80 cm
40 inches / 101 cm
46 inches / 116 cm
55 inches / 138 cm
Display area
697.6845 mm (H) x 392.256 mm (V)
27.5 inches (H) x 15.4 inches (V)
885.6 mm (H) x 498.15 mm (V)
34.9 inches (H) x 19.6 inches (V)
1018.08 mm (H) x 572.67 mm (V)
40.1 inches (H) x 22.5 inches (V)
1209.6 mm (H) x 680.4 mm (V)
47.6 inches (H) x 26.8 inches (V)
Dimensions (W x H x D)
736.0 x 434.5 x 93.7 mm
29.0 x 17.1 x 3.7 inches
925.4 x 541.0 x 93.6 mm
36.4 x 21.3 x 3.7 inches
1057.7 x 615.8 x 94.8 mm
41.6 x 24.2 x 3.7 inches
1247.7 x 722.9 x 94.8 mm
49.1 x 28.5 x 3.7 inches
Weight (Without Stand)
6.0 kg / 13.2 lbs
11.4 kg / 25.1 lbs
11.9 kg / 26.2 lbs
18.3 kg / 40.3 lbs
VESA
200 x 200 mm / 7.9 x 7.9 inches
400 x 400 mm / 15.7 x 15.7 inches
Display Colour
8bit , 16.7M (ED32C) 10bit(Dithering), 1.07B(ED40C, ED46C, ED55C)
Synchronization
Horizontal
Frequency
30 ~ 81 kHz
Vertical
Frequency
46 ~ 75 Hz
Resolution
Optimum
Resolution
1920x1080@60Hz, 1366x768@60Hz(ED32C Only)
Maximum
Resolution
1920x1080@60Hz
Maximum Pixel Clock
148.5MHz (Analogue,Digital)
Power Supply
This product uses 100 to 240V. Refer to the label at the back of the product as the standard voltage can vary in different countries.
Signal connectors
Input
PC D-Sub, HDMI, Audio In, RS232C In, USB(Service Only)
Output
Audio Out, RS232C Out
Environmental
considerations
Operating
Temperature : 50˚F ~ 104˚F (10˚C ~ 40˚C) / Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4˚F ~ 113˚F (-20˚C ~ 45˚C) / Humidity : 5 % ~ 95 %, non-condensing
PowerSaver
Rating
70 Watts
100 Watts
110 Watts
150 Watts
Typical
47 Watts
76 Watts
88 Watts
120 Watts
Max
77 Watts
110 Watts
121 Watts
165 Watts
Power saving mode
(SOG Signal : Not Support
the DPM Mode)
0.5 Watts
0.5 Watts
0.5 Watts
0.5 Watts
Power off
0.5 Watts
0.5 Watts
0.5 Watts
0.5 Watts
Power off
(Power Swich)
0 Watts
0 Watts
0 Watts
0 Watts
- Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes place
automatically. However, you can customize the installation settings if desired.
- Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the LCD panel. This does not affect product performance.
- This device is a Class A digital apparatus.
POWER IN
ON
ON
Server PC /
Serveur PC
RS232C
IN OUT
RS232C
IN OUT
BN68-04953C-00.indd 2
2013-02-06 5:42:07
