Samsung AR TXFY Series Скачать руководство пользователя страница 6

Страница: 6 / 32

Safety Information

English

Saf
ety
Inf
or

mation

•

Make sure that the labels are affixed on the system to

notify it contains flammable refrigerant.

Recovery

•

When removing refrigerant from the system for

servicing or decommissioning, it is recommended to

remove the entire refrigerant.

•

When transferring refrigerant into cylinders, make sure

that only the refrigerant recovery cylinders are used.

•

All cylinders used for the recovered refrigerant shall

be labelled.

•

Cylinders shall be equipped with pressure relief valves

and shut-off valves in a proper order.

•

Empty recovery cylinders shall be evacuated and

cooled before recovery.

•

The recovery system shall operate normally according

to the specified instructions and shall be suitable for

refrigerant recovery.

•

In addition, the calibration scales shall operate

normally.

•

Hoses shall be equipped with leak-free disconnect

couplings.

•

Before starting the recovery, check for the status of the

recovery system and sealing state. Consult with the

manufacturer if suspected.

•

The recovered refrigerant shall be returned to the

supplier in the correct recovery cylinders with the

Waste Transfer Note attached.

•

Do not mix refrigerants in the recovery units or

cylinders.

•

If compressors or compressor oils are to be removed,

make sure that they have been evacuated to the

acceptable level to ensure that flammable refrigerant

does not remain in the lubricant.

•

The evacuation process shall be performed before

sending the compressor to the suppliers.

•

Only the electrical heating to the compressor body is

allowed to accelerate the process.

•

Oil shall be drained safely from the system.

•

For installation with handling the refrigerant (R-32),

use dedicated tools and piping materials. Because the

pressure of the refrigerant, R-32 is approximately 1.6 times

higher than that of R-22, failure to use the dedicated

tools and piping materials may cause rupture or injury.

Furthermore, it may cause serious accidents such as water

leakage, electric shock, or fire.

•

Never install a motor-driven equipment to prevent

ignition.

Power supply line, fuse, or circuit breaker

•

Be sure not to perform power cable modification,

extension wiring, and multiple wire connection.

‐

It may cause electric shock or fire due to poor

connection, poor insulation, or current limit

override.

‐

When extension wiring is required due to power

line damage, refer to "Step 2-5 Optional: Extending

the power cable" in the installation manual.

Содержание AR TXFY Series

































Результаты поиска

Содержание AR TXFY Series

Отзывы:

Похожие инструкции для AR TXFY Series

Бренды по названию

Популярные бренды

Samsung AR TXFY Series, Руководство по установке

Результаты поиска

Содержание AR TXFY Series

Отзывы:

Похожие инструкции для AR TXFY Series

Бренды по названию

Популярные бренды