Samsung AR**HS Скачать руководство пользователя страница 18

Страница: 18 / 25

English

Ins
tallation

If using a multi system, install as described in the
installation manual supplied with the outdoor unit.

Step 3.1 Fixing the outdoor unit in
place

Place the outdoor unit as directed on the top of the
unit to let the discharged air out properly.

Fix the outdoor unit in level to an appropriate support
using anchor bolts.

NOTE

•

Secure the rubber legs to help prevent the generation
of noise and vibration.

•

If the outdoor unit is exposed to strong winds, install
shield plates around the outdoor unit so that the fan
can operate correctly.

•

Optional: Fixing the outdoor unit to a wall with
a rack

NOTE

•

Make sure that the wall can support the weights of the
rack and the outdoor unit.

•

Install the rack close to the column as much as
possible.

Step 3.2 Connecting the power
and communication cables and the
refrigerant pipes

CAUTION

•

Be sure to fix the power cables and communication
cable with a cable clamp.

•

Power & Communication cable shall not exceed 30m.

Outdoor Unit Installation

(Unit : mm)

Model



09/12



AJ040/050



612

317

AJ052/060/070/080



660

340

AJ100



620

360

Rubber leg

Soft rubber designed to cut off vibration from

rack to wall (not supplied with product)

Soft rubber designed to cut off residual vibration

from outdoor unit to rack (not supplied with product)

Outdoor-to-indoor

power cable

(three wires)

Communication cable

(two wires)

Power cable

(three wires)

A3050_EU_Best model_IM_DB68-06152A-00_EN.indd 17

2016/4/20 14:10:23

Содержание AR**HS


























Результаты поиска

Содержание AR**HS

Отзывы:

Похожие инструкции для AR**HS

Бренды по названию

Популярные бренды

Samsung AR**HS, Руководство по установке

Результаты поиска

Содержание AR**HS

Отзывы:

Похожие инструкции для AR**HS

Бренды по названию

Популярные бренды