Samsung AEGIS WF-M592NMH Скачать руководство пользователя страница 49

Страница: 49 / 59

34 _ Troubleshooting

4. TROUBLESHOOTING

4-1. ERROR MODES

►

This is a washer integrated error mode. For detailed information, refer to the general repair scripts.

Error Type

Drum

Fully

automatic

Causes

Remarks

Error

mode

Old

error

mode

For USA

Water Level

Sensor

1E
E7

- The part of the hose where the water level sensor

is located is damaged (punctured).

-  The hose is clogged with foreign material.
-  The hose is folded.
-  Too much lubricant has been applied to the

insertion part of the air hose.

-  Hose engagement error (disengaged)
-  Part fault (Faulty internal soldering)
-  The water level sensor terminal is disengaged.
-  Main PBA fault.

Motor Driving

Error and Hall

Sensor Error

3E
EA

-  The PBA connector terminal is not connected.
-  The motor spin net is not engaged.
-  The motor’s internal coil is damaged (short-

circuited or cut)

- The hall sensor terminal is not connected.
- Foreign material (a screw) has entered the motor.

For USA

products, this

error occurs

because of

restrained

revolutions

3E1

- Motor overloaded due to too much laundry (Non-

sensing)

- The motor hall sensor terminal is not connected.
- PBA fault

For USA

products, this

error occurs

when an

interference is

generated due

to too much

laundry, etc.

3E2

- The motor driving error from the PBA is weak.

: Unstable relay operation, etc.

3E3

- This occurs due to erroneous operating signals

for the motor hall sensor.

- The IPM terminal of the main PBA is not

connected.

- The DD motor cover is out of place.

3E4

-  The PCB housing terminal is not connected.
-  PBA fault
-  DD motor fault

Water Supply

Error

4E
E1

- Foreign material is entering the water supply

valve.

- The water supply valve terminal is not connected.

(Wire disconnected)

- The warm water and rinse connectors are wrongly

connected to each other.

- This occurs if the PCB terminal from the drain

hose to the detergent drawer is not connected.

Check whether the transparent hose is folded or

torn.

If this error

occurs in the

Wool course

4E1

4Ed

- The cold and warm water supply hoses are

wrongly engaged into each other.

- The temperature of the water supplied through

the dry valve during a dry cycle is sensed as

higher than 70 ˚C.

The water

supplied for 1

minute drying

the drying cycle

is 0.3 ~ 0.4 L.

4E2

- The water temperature is sensed as higher than

50 ˚C in the Wool or Lingerie courses.

WF-M592NMH-YLP.indb 34

2010-2-22 13:29:57

Содержание AEGIS WF-M592NMH




























































Результаты поиска

Содержание AEGIS WF-M592NMH

Отзывы:

Бренды по названию

Популярные бренды

Samsung AEGIS WF-M592NMH, Руководство по обслуживанию

Результаты поиска

Содержание AEGIS WF-M592NMH

Отзывы:

Бренды по названию

Популярные бренды