Samsung AE050RXYDEG Скачать руководство пользователя страница 73

Страница: 73 / 122

Troubleshooting

Samsung Electronics

Error mode

Contents

Measure

Product operation in

error condition

Error type

Outdoor unit/

Compressor/Indoor

unit

Gas leak error

Check the coolant charging status

Check the indoor EVA sensor.

Check if the outdoor unit service value is open.

Check that the indoor/outdoor installation pipe/wiring

are correct.

Operation Off

Self diagnostic

error

Inverter EEPROM loading error Check EEPROM DATA.

Check the normal operation of PCB.

Operation Off

Comp down

error

Communication error between

the Hydro Unit and wired

remote controller

Check the Indoor unit PBA and wired remote controller .

Operation Off

communication

error

Wired remote communication

error

Communication tracking error between the CONTROL

KIT and wired remote controller.

Operation Off

Wired Remote

Controller

Wired remote controller

temp sensor SHORT or OPEN

Check sensor connection status.

Operation Off

wired remote

controller

sensor error

Memory(EEPROM) Read

Write error(Wired remote

controller data error)

Check the wired remote controller .

Operation Off

communication

error

Zone 1 water-out temperature

sensor error

Short- or open-circuit error of the Zone 1 water-out

temperature sensor.

Operation Off

Indoor Unit

error

Zone 2 water-out temperature

sensor error

Short- or open-circuit error of the Zone 2 water-out

temperature sensor.

Operation Off

Indoor Unit

error

Water inlet (PHE) temperature

sensor error

Refer to details.

Water outlet (PHE)

temperature sensor error

Refer to details.

Water outlet (backup heater)

temperature sensor error.

Refer to details.

DHW tank temperature sensor

error

Refer to details.

Refrigerant gas inlet (PHE)

temperature sensor

Refer to details.

Low flow rate error

Refer to details.

Normal flow rate error

Refer to details.

Thermostat wrong connection

error

Check the wiring of Hydro Unit Thermostat.

Check the Cooling /Heating signal : Concurrent wiring or

not.

Operation Off

Indoor sensor

error

Mixing Valve Outlet

temperature sensor error

Refer to details.

Error for disinfection operation

Error that the set temperature for disinfection operation

is not reached, or, after reaching, the temperature fails to

continue for the requested time.

Indoor Unit

error

Wired remote controller (cont.)

Содержание AE050RXYDEG



























































































































Результаты поиска

Содержание AE050RXYDEG

Отзывы:

Похожие инструкции для AE050RXYDEG

Бренды по названию

Популярные бренды

Samsung AE050RXYDEG, Руководство по обслуживанию

Результаты поиска

Содержание AE050RXYDEG

Отзывы:

Похожие инструкции для AE050RXYDEG

Бренды по названию

Популярные бренды