Samsung AC BNPDBC Series Скачать руководство пользователя страница 23

Страница: 23 / 76

English

US
ING P

Refer to following chart if the air conditioner operates abnormally. This may save time and unnecessary
expenses.

Troubleshooting

Problem

Solution

The air conditioner
does not work at
all.

• Check power status and then operate the air conditioner again.

• Check whether the power plug is connected correctly or the auxiliary power

switch is switched on.

• If the air conditioner is switched off by the Timer function, press the

On/Off

button.

The temperature
adjustment is not
working.

• Temperature adjustment is not available when the Fan mode is selected.

Fan speed
adjustment is not
working.

• Check if you have selected Auto/Dry/Turbo mode. In these modes, fan speed is

set to Auto and you cannot adjust the fan speed.

Remote controller
does not work.

• Replace the exhausted batteries with new ones.

• Do not block the remote controller receiver.

• If the remote controller is used near strong light(3-wavelength fluorescent

light, neon sign etc.), the remote controller may not work due to the electronic
jamming signal

Cool air does not
come out of the air
conditioner.

• Check if the set temperature is higher than the current temperature. Press the

Temp

button on the remote controller to set the temperature lower than

the current temperature.

• Check if you have selected Fan mode. In this mode, Cool air will not come out in

Fan mode therefore select Auto/Cool/Dry mode.

• Check if the air filter is blocked by dirt. If there is a lot of dust on the Air filter,

cooling performance may decrease. Clean them frequently.

• Check if the outdoor unit is covered or installed near the obstacle. Take the cover

off and take the obstacle away.

• Check if the indoor unit is installed in a place with direct sunlight. Close the

curtain or blind to cover the sunlight.

• If the doors or windows are open, it may cause bad cooling performance. Close

the doors and windows.

• If the air conditioner has just been turned on or the indoor temperature reaches

the desired temperature, only fan will operate around 3 minutes for the product
protection.

• Check if the pipe length is too long. When the pipe length exceeds maximum

allowable pipe length, cooling performance may decrease.

ki]_TXX^ZXjTWWpiptwhjGz{jluUGGGYZ

YWYYTW[TW_GGG㝘㤸G`aXYa[[

Содержание AC BNPDBC Series













































































Результаты поиска

Содержание AC BNPDBC Series

Отзывы:

Samsung AC BNPDBC Series, Руководство пользователя и инструкция по установке, Страница: 23 / 76

Результаты поиска

Содержание AC BNPDBC Series

Отзывы: