Sammic MO-1817, Инструкция по эксплуатации

Страница: 19 / 64

19 - 19 -
ES EN
3. If press “ ” at the last step, it will turn back to Ready Mode.
The setting will be no use.
13.
Double/Triple Quantity cooking
1) If the “X2” or “X3” button is pressed in Ready Mode, followed
by the starting of a Preset Program, or if the “X2” or “X3” but-
ton is pressed in 5 seconds of starting a Preset Program, the
oven will start cooking with the quantity preset cooking time.
2) Press “X2”, “DOUBLE” displays. Press “X3”, “TRIPLE” dis-
plays. When press number buttons, the screen will display the
quantity preset time.
For example, number button “5” and its preset time is 1 minute.
Then press “X2”, then time will change to 1:00*2=2 (2 minutes)
3) When cooking program finish, the oven will enter End of Cook
Cycle Mode.
14.
Stage Cooking Programming
This allows the user to cook food items at manual cook mode
and programming mode.
1) Three stages can be set at most under cooking mode or pro-
gramming mode.
After setting the power and time for the first stage, press
“Time Entry” to set the second stage. And the same step
to set the third stage.
2) When setting the second, third stage, press “Time Entry”,
“STAGE-2”, “STAGE-3” displays.
3) Press “ ” button to start cooking.
Example: In programming mode, press number buttons “3” to set
two stages cooking. The first stage is PL7 and time is 1 minute 25
seconds. The second stage is PL5 and 5 minutes and 40 seconds.
The steps are as follows.
a. Open the door, press number button “1” for 5 seconds,
“PROGRAM” displays.
b. Press number button “3”, the screen will display “P:03”.
After two seconds, the screen will display the related time “:30”.
c. Press “1”, “2”, “5” to input the cooking time. “1:25” displays.
d. Press “Med-Hi 70%”, “1:25 70” displays.
The first stage is finished.
e. Press “Time Entry”, “STAGE-2” displays.
f. Press “5”, “4”, “0” button, “5:40” displays.
g. Press “Medium 50%”, “5:40 50” displays.
The second stage is finished.
h. Press “ ” button to start cooking.
i. The total time counts down.
15.
Filter Cleaning Function
1) If User Option OP:01 is selected and the setting time arrives,
the oven will remind the user to cleaning the filter.
Note: The oven must be electrified.
2) The screen will display “CLEAN FILTER”. At this time, pressing
“ ” button or opening the door will put the oven into Ready
Mode.
3) If you do not need to clean the filter, press “ ” button and hold
for 3 seconds to clear out the reminder information. Otherwise,
the oven will remind you all the time during Idle Mode.
16. Use Option Mode
This allows the user choose between various ways for the oven
to operate.
1) Open the oven door and press “2” pad for 5 seconds. The
buzzer sounds once and enter this mode.
2) The screen displays “OP: - -”.
3) Press any number button to enter related mode setting.
For example: to set the voice of the buzzer to medium. Press
“2”, “OP:22” displays.
If you want to change, keep pressing “2”, the screen displays
“OP:20”, “OP:21”, “OP:22”, “OP:23”, “OP:20” in cycle.
4) Press “ ” to save the current setting. After saved, “OP: - -”
display again.
5) During setting process, press “ ” to enter Door Open Mode.
Close the door will enter Ready Mode.
6) If “ ” button not pressed at the last step, the program cannot
be saved but stay at previous way.
17. Factory-default setting
In the Ready Mode, pressing “ ” and “0” to factory-default
setting.
1) Press “ ” and “0”, the buzzer sounds once, and the screen will
display “CHECK”.
If it is in the factory-default setting, the screen will display “11”,
after three seconds, the oven turn to the ready mode Press
“ ” to cancel the display ang back to ready back in the pro-
cess of display.
If not in the factory-default setting, the screen will display “00”,
press “ ” to the factory-default setting, the screen will display
“CLEAR”. the buzzer sounds once, after self-testing, the screen
will display “11” or “00”.
2) If do not press “ ” when the screen display “00”, the setting
will cancel.
Note: Be careful in the operation as it will restore all configure to
factory-default setting.