background image

2. It may affect the normal use or charge of the battery, if it is covered with dust. Please clean the battery with dry cloth before
loading or charging it.

Knowledge about Battery Storage

1. Since the battery will self-discharge, please do charge it fully before putting it aside so as to prevent damages caused by
over discharge.
2. Please take out the battery after storage for some time to fill it, in order to avoid the reduction of the battery capacity resulting from
over discharge. It is proposed for lithium-ion / lithium-polymer batteries to be filled in every 6 months of storage.
3. Please pay attention to the humidity of the battery storage environment. Batteries are supposed to be stored in the
environment of room temperature, cool and dry air, to reduce the self-discharge.

Charging Operation

Please use SAMCOM-specified charger to charge the battery; the indicator light of the charger shows the completion of charging 
operation.

Red light                
Green light            
Please do the following steps to charge:

State

 Be charging
 Charging completed

Indicator Light       

g

p

g

1. Insert the AC plug of the power adapter into the AC power outlet.
2. Insert the DC plug of the power adapter into the DC jack on the
back of the charger, 

3. Place the battery or the transceiver with battery on the charger.

4. Confirm that the battery contacts are well connected with the charger contacts, and the charge indicator light turns red, which

represent the beginning of the charging operation.

5. After a period of time, when the indicator light turns green, it shows the completion of the charging operation.

Installation/Removal of the Battery
1. Installation of the Battery

Please make sure the transceiver is powered off, and then hold down the belt clip to open it , 
Hold down the two side keys and  insert the two bumps on the top of the battery into 
the aluminum grooves of the transceiver in the direction of the arrow, and to finish the installation, 
press the bottom of the battery in the direction of the arrow until the “ka-ta” sound is heard.

Note:

 If the battery is not fixed well, please remove it and reinstall.

Содержание FPCN30A

















Отзывы: