SaMASZ Z2-780 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

SaMASZ Z2-780 Скачать руководство пользователя страница 23

Operator’s manual

Twin-rotor rotary rake

Z2-780; Z2-840

- 21 -

S

K

Fig. 16.

Rake wheelbase refitting

When the rake is in working position, please do the following:



connect PTO shaft extension onto tractor's spline shaft (if only one extension was taken out) or
connect the complete PTO shaft,



using regulation lever (lift or lower) adjust the desired working height height (

not lower

than 1 cm / 0.39”

above the ground

),

Fig. 17.

Working height adjustment lever

CAUTION:

It is forbidden to lower raking arms below 1 cm from the ground as this may
cause damages to the machine such as bending the raking arms, breaking the
linkage or the gear, faster wearing of raking tines, damaging the turf and
causing contamination to the collected forage, etc. Too high a raking set may
cause the swath not be collected completely.

CAUTION:

The raking arms' height should be controlled on an on-going basis while
operating the machine, and if need be, adjusted. Adjustments are performed
with tractor's drive off.



turn on tractor’s PTO and work at moderate rpm rate e.g. 300÷350 rpm. Long work at the
nominal rate of 540 rpm. will cause premature wear of gearbox,



engage tractor gear and drive slowly into the row. Working speed affects the clean raking.

«
...
21
22
23
24
25
...
»

Содержание Z2-780













































Отзывы:

Нет отзывов