manualshive.com logo in svg

SaMASZ KDC 260 S, Руководство оператора

Поделиться
Скачать
SaMASZ KDC 260 S Скачать руководство пользователя страница 37

Operator's manual 

Trailed disc mowers 

KDC

 

 
 

- 35 - 

NOTE:

 

When performing maintenance or adjustment works underneath the mower, 
use adequate locks for lifted parts of the machine preventing their falling and 
risk of crushing. 

 

6.10.2.

 

Off-season maintenance and storing 

 

It is recommended for the operator to wear protective gloves when performing 

maintenance works. 

. 

Upon completion of operation: 

 

lower the mower’s cutterbar onto the ground, 

 

take  the  PTO  shaft  extension  out  of  the  tractor  rpm  or  dismount  the  complete  PTO  shaft  and 
install it into corresponding holder at the 3-point linkage frame, 

 

detach  hydraulic  and  electrical  hoses  out  of  the  tractor  and  hang  them  onto  corresponding 
holders on the 3-point linkage frame, 

 

detach the mower from the tractor (reverse procedure as in case of attaching the mower to the 
tractor see item 5.1), and then drive the tractor away. 

It  is  recommended  to  store  the  mower  on  paved  ground,  preferably  in  roofed  places, 

inaccessible to unauthorized personnel. Machine should be stored in dry place, in the event if it is 
exposed to precipitations, apply lubrication regularly. 

 

At  the  end  of  the  season  the  mower  should  be  cleaned,  washed  and  dried.  Carefully  grease 

unpainted surfaces and 3-point linkage pins. 

Moreover: 

 

perform any necessary paintwork repair, 

 

examine  oil  level  in  axis  gears  and  cutterbar  (item  7).  If  leaks  are  found  remove  them 
immediately  and  refill  the  oil.  If  water  is  found  in  the  oil,  it  must  be  replaced;  otherwise  the 
gears,  bearings  and  shafts  could  be  exposed  to  corrosion  what  in  result  could  lead  to  further 
failures. 

 

perform periodic checkups of the mower and protect all operating parts with grease in order to 
prevent  their  baking  and  creating  any  sources  of  corrosion,  which  significantly  influences 
mower's proper operation. 
 

After storage period, before the machine is used: 

 

check the mower's technical condition, and the transmission in particular, 

 

supplement the paint where missing, 

 

make sure that all nuts and screws are tightened properly, 

 

make sure that all guards are in place, 

 

protect all moving parts with grease in order to prevent their baking and creating any sources of 
corrosion, which significantly influences mower's proper operation, 

 

check  oil  level  in  axis  gears  and  cutterbar.  If  leaks  are  found  remove  them  immediately  and 
refill the oil. If water in oil is found, immediately change the oil as it could cause corrosion of 
internal mechanisms such as gear wheels, bearings, or shafts, and cause breakdowns. 
 
 
 
 
 
 
 
 
 

Содержание KDC 260 S





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды