Sam IQFDA31 Скачать руководство пользователя страница 19

Страница: 19 / 24

IQFDA31

Operation Using the RollCall Control Panel

Issue 1 Rev 1

Page 19

5.5.4 Log Field Descriptions

Log Field

Description

SN=

The module’s unique serial number.

OS_VERSION=

The operating system version.

BUILD_NUMBER=

The software build number.

HARDWARE_VERSION

The hardware build version.

UPTIME=

Shows the time since the last restart (format
ddd:hh:mm:ss).

LICENSED_OPTIONS=

The licensed features installed in the module.

ROL_STATES=

The status of any RollTracks that have been enabled.

REAR_ID=

The rear panel type.

REAR_STATUS=

The status of the rear panel.

SLOT_WIDTH=

The number of slots used by rear and module.1 or 2.

SLOT_START=

The first slot number the rear occupies. Use in
conjunction with SLOT_WIDTH to determine the slots
that the unit occupies.

LAST_RECALLED_MEMORY=

The last recalled memory.

POWER USAGE=

The power rating for the module. Note: this is not a live
power reading.

INPUT_

_IDENT=

The identifier of the serial data input.

INPUT_

_NAME=

The name of the serial data input.

INPUT_

_TYPE=

This displays the type of input as specified by the unit’s
configuration. Valid values are HD /SD SDI.

INPUT_

_STATE=

Displays the current input state. Valid values are:

•

WARN:Mismatch

•

FAIL:Lost

•

FAIL:Error

Note: WARN:Mismatch indicates that the input and
output standards are not the same.

INPUT_

_SDIRATE=

The current bit rate for the serial data input.

SFP_

_TYPE=

The transmitter type.

SFP_

_STATUS=

The status of the SFPs as reported by the SFPs.

SFP_

_CONNECTOR=

The physical connector type, for example, Fiber LC.

OUTPUT_

_TX_POWER_STATE=

Displays the TX power status. Valid values are:

•

WARN:HI

•

WARN:LO

•

FAIL:LO

•

FAIL:HI

OUTPUT_

_TX_POWER=

The power level of the TX input, in dBm.

OUTPUT_

_WAVELENGTH=

The wavelength of the transmitted output signal.

Содержание IQFDA31

























Результаты поиска

Содержание IQFDA31

Отзывы:

Похожие инструкции для IQFDA31

Бренды по названию

Популярные бренды

Sam IQFDA31, Руководство пользователя

Результаты поиска

Содержание IQFDA31

Отзывы:

Похожие инструкции для IQFDA31

Бренды по названию

Популярные бренды