Saluki TAM4000 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 33

Saluki TAM4000 Скачать руководство пользователя страница 32

Tel: 886.909 602 109 Email: [email protected]

www.salukitec.com

32

6 Common Problems

6.1 Daily Maintenance

The equipment should be kept in a dry and room temperature environment and charge
regularly. It is usually charged once in three months, and the charging time is 8 to 12
hours.
Equipment should avoid long time exposure in the sun, to avoid long time used under
low temperature (below 10

℃

). Otherwise, it will damage the liquid crystal and cause

aging of the shell.
Try to avoid the use of rain. If you can't avoid rain and moisture, the equipment will
be damaged in the shortest time.
In the process of use, if the abnormality of the instrument is found, please contact the
manufacturer in time, so as to avoid the delay of work.

6.2 Correct Charging

Will charger connected to the AC 50 hz, 220 V mains charger indicator (green), and
then insert the charging head instrument charge (charged host in shutdown state), the
charger indicator lights turn red, charging system showed normal, after a period of
time charge indicator from red to green, doesn't mean the battery is full of charge at
the moment, just shows the charger from the large current quick charge state to small
current slow filling state, just make sure reach 8 to 12 hours charging time. If the
transmitter after charging head inserted into the host seat (charged host in shutdown
state), charger red light is the same, and boot and no show, show machine inside the
battery loose or poor contact, open the battery cover plate will be installed at this time.

6.3 Instrument Self-inspection

Panel check

1. Transmitter: function brief to operate each key is normal.
2. Receiver: it is normal to operate each key of the function profile.

Work status check

1. Signal output and acceptance inspection.
Straight line multi-fiber head inserted into the transmitter multi-fiber airline seats,
separate line straight and short answer the two clip, press the transmitter power switch,
impedance Ω according to 1. Icon rotation.
Hand-held receiver located near by the straight line, press the power switch receivers,
and choose to set the receiver to the same frequency wave method, after a few

«
...
30
31
32
33
»

Содержание TAM4000


































Отзывы:

Нет отзывов