SALSBURY INDUSTRIES
18300 Central Avenue, Carson, CA 90746-4008
Phone: 1-800-562-5377
Int’l Phone: 323-846-6700
Fax: 1-800-562-5399
Int’l Fax: 323-846-6800
www.lockers.com
engineering
@
lockers.com
Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.
Copyright ©
2020
Salsbury Industries. All rights reserved. (Rev. 07, 2/17/2014) Page 1 of 2
Electronic Locker Locks – 3090, 11190, 22290, 30090, 33390, 77790
Operation & Programming Instructions
The electronic locker lock is a cost-effective and easy-to-use lock
providing keypad access without the need for keys. It is designed
with simplicity in mind, including programming.
The lock has a simple five (5) button, dual action keypad (0-9) and a
# button, which is used for programming. When the lock is locked
(closed), the # button is covered by the lock handle.
Please read this entire document before use.
USER OPERATION
To open the lock, simply punch in a four (4) digit user code (e.g.
2244 is the factory default code) and turn the handle located just
under the ten (10) digit keypad. A blue LED blinks once after each of
the first three (3) digit entries and blinks blue again if all four (4)
entries were correct. Otherwise, it blinks red after the fourth entry if
one or more digits were incorrectly entered.
How to Read This Document
means blue LED flashes one time.
means blue LED flashes two times.
means red LED flashes one time.
means red LED flashes two times.
means red LED flashes three times.
#
means press the red “#” button under the handle at the bottom of
the lock front panel.
MasterCode
means enter the master code number (8 digits).
SubMasterCode
means enter the sub-master number (8 digits).
UserCode
means enter the user code number (4 digits).
CODES – The Basics
The locker lock has three code levels available:
1. Master Code
2. Sub-Master Code
3. User Code
The locker lock is supplied with two factory set codes:
1. Master Code: 11 33 55 77
2. User Code: 22 44
When fitted, immediately change the Master Code and User Code.
All Master Codes and Sub-Master Codes are 8 digits long.
All User Codes are 4 digits long.
The lock “open” time is set at 4 seconds.
Functions
Before programming, select the most appropriate function for the
application: REPEATED USE or SINGLE USE. For complete
programming instructions, please see reverse side of this sheet.
A) REPEATED USE
Important Note: This is the default function and is already pre-
programmed in new locks.
This is the most common function and
is used where the
same code
will be
repeatedly used
.
B) SINGLE USE
The User enters a single use code which will lock and then open the
lock
once only
and then be erased. This function is used for short
term, multi-occupancy applications (e.g. a locker in a leisure center).
To select B) SINGLE USE:
#
MasterCode
24
The lock will now remain open until the next single use code is
entered into the lock as follows:
Step 1 Enter 4 digit code
.
Close the locker which will now be locked.
Step 2 Enter same 4 digit code
.
Lock will now open and remain open until the next 4 digit code is
entered.
Example: Step 1 1234
.
Close the locker, which will now be locked.
Note:
When locked in
this mode, the red
LED will flash every 5 seconds to indicate
locker is locked.
Step 2 1234
. Locker now open – remains open until next
single use code is entered.
Note:
To reset to default function
A)
, use following key sequence:
MasterCode
26
Example: 11 33 55 77
26
OPERATING INSTRUCTIONS
Note:
The locker lock has a 10 button keypad and a # button. The #
button is hidden beneath the handle when in the locked position.
The lock has the following code levels:
The
Master Code
can:
Open the lock.
