Sakura GP-CP06 Скачать руководство пользователя страница 7

Страница: 7 / 8

Troubleshooting

Problem

Possible Cause

Likely Solution

The Polisher

will not start

The power cord is not

plugged in. There is an issue

at the mains power supply.

The Polisher is not turned on

Check the power cord

is plugged in. Check the

power at the mains. If there

is no power, check the

circuit connections

Turn on the polisher

The Polisher

is operating

slowly

Excess pressure has been

applied to the Polisher

Decrease pressure applied

Excessive noise

or rattling

Internal wear or damage

Do not use the machine

Overheated

Blocked vents or used

continuously for too long

Allow unit to cool

Clean out the dust from

the vents (whilst power is

disconnected) with a fine

brush or compressed air

The Polisher

does not polish

effectively

The accessory may be worn

Replace accessory

Содержание GP-CP06









Результаты поиска

Содержание GP-CP06

Отзывы:

Похожие инструкции для GP-CP06

Бренды по названию

Популярные бренды

Sakura GP-CP06, Инструкция по эксплуатации

Результаты поиска

Содержание GP-CP06

Отзывы:

Похожие инструкции для GP-CP06

Бренды по названию

Популярные бренды