Sakura Dry-Boy SDB-45 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 10

Sakura Dry-Boy SDB-45 Скачать руководство пользователя страница 10

DUCT KIT ASSEMBLY

10

Installer’s & Owner’s Manual

FRONT DUCT ASSEMBLY

1. Check sealing foam on the front duct assembly. Ensure that

none has come loose.

2. Place front duct assembly on the intake side of the

dehumidiﬁer.

3. Center the front duct assembly. Ensure the sealing foam makes

contact around the plastic intake grill surface. Sealing foam
should not cover any of the inlet portion of the intake grill.

4. DO NOT DRILL PILOT HOLES FOR SCREWS. You will risk

possibly damaging the internal components.

Using the

through holes provided in the top duct assembly, screw in the
four 10-16 X 1/2 screws directly into the plastic housing (see
Figure 1 — screws indicated in white circle). Be careful not to
strip loose. Lightly tighten screws. Do this in all four through
hole locations.

TOP DUCT ASSEMBLY

1. Check sealing foam on the top duct assembly. Ensure none has

come loose.

2. Place top duct assembly, ensure the sealing foam makes

contact around the plastic surfaces.

3. Center the top duct assembly, ensure the sealing foam makes

contact around the plastic surfaces.

4. Ensure the rear ﬂange of the top duct assembly is seated ﬂush

against the back of the plastic housing. See Figure 2.

5. DO NOT DRILL PILOT HOES FOR SCREWS. You will risk

possibly damaging the internal components.

Using the

through holes provided in the top duct assembly, secure back
ﬂange of the top duct assembly ﬁrst. Drive two 10-16 X 1/2
screws directly into the plastic housing. After the back ﬂange
has been secured, drive in the last two screws (located on the
top) into the plastic housing using the same procedure.

6. Start unit and check for any air leaks around the perimeter of

the ducts.

7. If any leaks are found, seal leak with foil tape.

Duct Kit Assembly Instructions Continued

FIGURE 1

FIGURE 2

«
...
8
9
10

Содержание Dry-Boy SDB-45











Отзывы:

Нет отзывов