manualshive.com logo in svg

Safran MorphoAccess SIGMA Extreme FFD iCLASS, Руководство по установке

Поделиться
Скачать
Safran MorphoAccess SIGMA Extreme FFD iCLASS Скачать руководство пользователя страница 53

MorphoAccess® SIGMA Extreme Series - Installation Guide 

 

Annex 1 : Finger Placement Recommendations 

Identity & Security

 

 

2017_2000024418 - V1 
April 2017

 

This document and the information therein are the property of 

Safran Identity & Security

. 

They must not be copied or communicated to a third party without the prior written authorization of Safran

 

53 

 

When authentication is initiated on the terminal, the terminal will poll the user ID to 
external  controller.  On  polling  out  the  ID,  the  corresponding  template  (if  exists)  is 
fetched from the external database and is authenticated against user’s biometric on 
the  terminal.  Once  the  template  request  is  posted  to  the  external  database,  the 
terminal  shall  wait  for  the  finger  template  from  the  external  database  to  start 
authentication. Further process shall be same as authentication. 

 

Polling Process using buffer:  

 

The  user’s  input  ID  will  be  queued  in  the  terminal’s  queue,  which  is  polled  by 

external application.  

 

External application waits for the User ID by polling the buffer. After getting an ID, 

it will search the template in database and send template to terminal for further 
authentication.  

 

The user is authenticated by the external device and granted access accordingly.  

 

MorphoAccess® SIGMA Extreme Series terminal also has distant commands to retrieve 
polling  buffer  status  and  polling  buffer  data.  Refer  to  the  MorphoAccess®  SIGMA 
Extreme Series Host System Interface Specification document. 

 

How to Activate? 

External  database  mode  can  be  activated  through  Webserver  >  Complete 
Configuration,  by  setting  “ucc.enable_external_database”  parameter  to  1.  Only  an 
admin  user  can  activate  polling  mode.  You  can  refer  to  the  MorphoAccess®  SIGMA 
Extreme Series Host System Interface Specification document to know how to set this 
parameter. 

 

Содержание MorphoAccess SIGMA Extreme FFD iCLASS
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды