Safran MorphoAccess SIGMA Extreme FFD iCLASS Скачать руководство пользователя страница 5

Страница: 5 / 79

MorphoAccess® SIGMA Extreme Series - Installation Guide

Table of Content

Identity & Security

2017_2000024418 - V1
April 2017

This document and the information therein are the property of

Safran Identity & Security

They must not be copied or communicated to a third party without the prior written authorization of Safran

Example of connection for electrical door locks .................................................................. 38

Tamper Switch ......................................................................................................................... 39

Operating principle for the switch ....................................................................................... 39

Nominal characteristics of switch block .............................................................................. 39

Wiegand wiring ....................................................................................................................... 40

Wiegand input ..................................................................................................................... 40

Wiegand output ................................................................................................................... 41

The controller supports neither LED1 nor LED2 signals ....................................................... 41

The controller supports only LED1 signal ............................................................................ 41

The controller supports LED1 and LED2 signals .................................................................. 42

Serial port wiring ..................................................................................................................... 43

DataClock Input ................................................................................................................... 43

DataClock Output ................................................................................................................ 43

RS485 ................................................................................................................................... 44

RS422 ................................................................................................................................... 44

GPIO wiring ............................................................................................................................. 45

Single Door Access Control (SDAC) implementation ........................................................... 45

Ethernet connection ................................................................................................................ 46

Default Ethernet configuration ........................................................................................... 46

Recommendations for RJ45 wiring ...................................................................................... 46

External USB connection ......................................................................................................... 47

Wi-Fi™ dongle installation ...................................................................................................... 48

Micro SD connection ............................................................................................................... 49

Section 5 : User Interface ........................................................................................................... 50

Modes for controlling access rights ........................................................................................ 51

Introduction ......................................................................................................................... 51

Identification mode ............................................................................................................. 51

Authentication (verification) mode ..................................................................................... 51

Multi-factor mode ............................................................................................................... 52

Proxy mode .......................................................................................................................... 52

External database mode (also called polling mode) ........................................................... 52

Configuring the terminal ......................................................................................................... 54

MorphoAccess® 500 or J Series legacy mode ...................................................................... 54

MorphoAccess® SIGMA Extreme Series native mode .......................................................... 55

Anti-tamper / anti-pulling switches ........................................................................................ 56

Section 6 : Accessories, Software Licenses and PC Applications ................................................ 57

Содержание MorphoAccess SIGMA Extreme FFD iCLASS














































































Результаты поиска

Содержание MorphoAccess SIGMA Extreme FFD iCLASS

Отзывы:

Бренды по названию

Популярные бренды

Safran MorphoAccess SIGMA Extreme FFD iCLASS, Руководство по установке

Результаты поиска

Содержание MorphoAccess SIGMA Extreme FFD iCLASS

Отзывы:

Бренды по названию

Популярные бренды