Safetec SDS-2/6 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 23

background image

safetec

Fault Finding Instructions SDS26

16.06.09

Seite 13 von 13

Problems with Fuses on Power Supply Module (SDS-2/6)

Blown

Fuse

Possible Reason

F1

Power supply module defective. Exchange power supply module.

F2

External short circuit on the bus cable. Please disconnect bus cable from
terminal nos. 17, 18, 19 and 20 at the power supply module and start
system again. If fuse does not break again, please examine the bus cable
to locate the short circuit.

F5, F6

Short circuit in fan unit no.1. Please disconnect cable for fan no.1 at
terminal nos. 5 and 6. and start system again. If fuse does not break again,
please examine the cable and fan motor no.1 to locate the short circuit.

F6, F7

Short circuit in fan unit no.2. Please disconnect cable for fan no.2 at
terminal nos. 7 and 8. and start system again. If fuse does not break again,
please examine the cable and fan motor no.1 to locate the short circuit.

«
...
11
12
13
14
15
...
»

Содержание SDS-2/6
























Отзывы:

Нет отзывов

Похожие инструкции для SDS-2/6

xComfort CSEZ-01/19

Бренд: Eaton Страницы: 6

Excalibur AL-1610-EDP

Бренд: Omega Страницы: 22

K-SMOKE-42-R-PW

Бренд: Kalamazoo Страницы: 64

Бренд: ZAZU Страницы: 8

Excalibur AL-1500-EDP

Бренд: Omega Страницы: 18

Large Display Alarm Clock

Бренд: Geemarc Страницы: 21

Бренд: La Crosse Technology Страницы: 14

Бренд: Silvercrest Страницы: 28

Бренд: Silvercrest Страницы: 46

Бренд: Silvercrest Страницы: 62

Бренд: Silvercrest Страницы: 69

Бренд: Silvercrest Страницы: 98

Бренд: Silvercrest Страницы: 140

Бренд: Silvercrest Страницы: 199

Бренд: Audiovox Electronics Страницы: 12

Бренд: Paradox Страницы: 12

BW-1000 AVENGER

Бренд: Black Widow Страницы: 2

BW-1500 CHALLENGER PLUS

Бренд: Black Widow Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды