manualshive.com logo in svg

SAF-HOLLAND SK RB 9022 K, Руководство по обслуживанию и ремонту

Поделиться
Скачать
SAF-HOLLAND SK RB 9022 K Скачать руководство пользователя страница 3

SAF axle identification 

2

Notes

4

Repairing the brakes

14-19

Replacing the tappets with tappet boots

20

Inspecting the adjuster thread

20

Installing the tappets with tappet boots

21

Sealing the brake calliper bearing with “seal kit for sliding guide”

22

Repairing the brake calliper bearing with “guide and seal kit”

23

Replacing the rubber guide sleeve

23-24

Replacing the brake calliper

24

Installing the brake calliper

25

Replacing the brake calliper carrier

26

Replacing the brake cylinder

26

Overview of hub unit components

27 

D) Installation instructions

Spare part illustration and spare part designation 
SK RB 9022 K / 9019 K - SK 1000 ET 120

12-13

C)

Spare part illustrations/spare part designation

B)

Maintenance instructions

Maintenance instructions for SAF axles 
SK RB 9022 K / 9019 K  – SK 1000 ET 120

6

Maintenance schedule for SAF axles 
SK RB 9022 K / 9019 K – SK 1000 ET 120

7

Brake testing (fault-finding procedure)

8

Adjuster check

9

Brake pad check

10

Special notes

11

3

Contents

Page

This manual is intended for the technical workshop personnel responsible for maintenan-
ce and repair.

A) General safety instructions 

5

E)

Service tools

28-30

The item numbers indicated are given only for identification and to distinguish between different versions.

Use the part numbers from the valid spare parts documents for identification of spare parts.

SAF axles and suspension units are subject to continuous further development; the data and drawings 
contained in the manual may therefore differ from the details given in the operating permit.

The contents of the manual does not constitute the basis for a legal claim.

Reprinting, reproduction or translation in whole or in part is not permitted.

The issue of this publication invalidates all earlier maintenance and repair manuals.

Note: We wish to thank KNORR-BREMSE for providing various illustrations!

F)

Tightening torque in Nm

31

Содержание SK RB 9022 K

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды