SAF-HOLLAND FW35 Series Скачать руководство пользователя страница 8

Страница: 8 / 32

XL-FW10009UM-en-US Rev F · 2021-06-16 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND,

HOLLAND, SAF, and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Figure 11

Figure 8

Figure 10

Figure 9

EXHAUST SUSPENSION AIR

BEFORE BACKING UP

7. Coupling Procedures

1. Chock the trailer wheels.
2. Position the tractor so the center of the

fifth wheel is aligned with the kingpin.

3. Traveling in a straight line, slowly back

the tractor to the trailer. STOP the tractor

before making contact with the trailer

(Figure 8)

4. Place the tractor into neutral and set

the parking brake.

5. Completely exhaust the air from the

tractor suspension, ensuring that

the fifth wheel is below the contact

surface of the trailer

(Figure 9)

6. Exit the cab and ensure that the fifth

wheel is below the upper coupler plate.

Verify proper fifth wheel height. If the

trailer is too low, use the landing gear

to raise the trailer height.

NOTE:

For proper operation of landing

gear, follow the instructions

published by the landing

gear manufacturer.

7. Slowly back up, using the lowest gear

possible. Stop when the fifth wheel is

under the leading edge of the trailer

(Figure 10)

8. Place the tractor into neutral and set the

parking brake. Exit the cab and verify

proper fifth wheel-to-kingpin alignment.

9. Adjust the tractor suspension to ride

height. The fifth wheel top plate face

MUST make contact with the upper

coupler plate

(Figure 11)

. If the fifth

wheel DOES NOT make contact with

the upper coupler plate, use the landing

gear to lower the trailer until the fifth

wheel makes contact.

IMPORTANT:

If the trailer is too high,

the kingpin will NOT

properly connect with

the lock jaws.

Operation Instructions

TRAILER

(TOP)

KINGPIN

BACK UP

AND STOP!

Содержание FW35 Series

































Результаты поиска

Содержание FW35 Series

Отзывы:

Похожие инструкции для FW35 Series

Бренды по названию

Популярные бренды

SAF-HOLLAND FW35 Series, Руководство пользователя

Результаты поиска

Содержание FW35 Series

Отзывы:

Похожие инструкции для FW35 Series

Бренды по названию

Популярные бренды